钻石40飞机维护手册 DA 40 SERIES AMM 6(9)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

One of the indicators in an  Sensor/Transducer defective.  Do a test for continuity of the 
integrated instrument does not  cables for the relevant sensor. 
indicate correctly.  One instrument defective  If the cables are serviceable, then refer to the engine manufacturer. Refer to Section 28-41 for the fuel quantity indicating system. Refer to Section 76-01 for the engine sensors. Replace the instrument. 

%

Doc # 6.02.01 Page 101
Rev. 4 09 Jan 2003

77-41-00
AMM

% Intentionally left blank
77-41-00
Engine Indicating
AMM

% Maintenance Practices % 1. General
% These maintenance practices tell you how to replace an integrated-engine-instrument and a manifold % temperature sensor. Refer to the related Chapter for maintenance data on the sensors.
% Where the engine control system provides data for the engine indicating system, only the engine % manufacturer or an TAE-approved maintenance shop can replace sensors.
% 2. Remove/Install an Engine Instrument
%
%

%
%
%
%
%
%
%
%
%
%
%
%

%

%
%
%
%

% A. Remove and Engine Instrument %

Detail Steps/Work Items  Key Items/References 
WARNING: MAKE SURE THE ENGINE IS SAFE BEFORE YOU DO ANY WORK ON IT. IF THE ENGINE STARTS THE PROPELLER CAN CAUSE INJURY OR DEATH. 
(1)  Make sure that the engine is safe: S Set the ELECTRIC MASTER key switch to OFF. S Set the ENGINE MASTER switch to OFF. S Set the power lever to IDLE. 
(2)  Remove the engine cowlings.  Refer to Section 71-11. 
(3)  Disconnect the airplane main battery.  Refer to Section 24-34. 
(4)  Remove the instrument panel cover.  Refer to Section 25-10. 
(5)  Disconnect the electrical connector from the instrument. 
(6)  Remove the 4 screws which attach the instrument to the instrument panel.  From the front of the instrument panel. Hold the instrument! 
(7)  Move the instrument towards the front of the airplane and clear of the instrument panel, then clear of the airplane. 

%

Doc # 6.02.01 Page 201
Rev. 4 09 Jan 2003

77-41-00
DA 40 Series
AMM

%
%

%
%
%

%
%
%

%
%
%

%

%
%
%
%
%
%
%

% B. Install an Engine Instrument %

Detail Steps/Work Items  Key Items/References 
WARNING: MAKE SURE THE ENGINE IS SAFE BEFORE YOU DO ANY WORK ON IT. IF THE ENGINE STARTS THE PROPELLER CAN CAUSE INJURY OR DEATH. 
(1)  Make sure that the engine is safe: S Set the ELECTRIC MASTER key switch to OFF. S Set the ENGINE MASTER switch to OFF. S Set the power lever to IDLE. 
(2)  Put the instrument in position in the instrument panel  From the front of the airplane. 
(3)  Install the screws which attach the instrument to the instrument panel. 
(4)  Connect the electrical connector to the instrument. 
(5)  Install the instrument panel cover.  Refer to Section 25-10. 
(6)  Connect the airplane main battery.  Refer to Section 24-34. 
(7)  Install the engine cowlings.  Refer to Section 71-11. 
(8)  Do an engine ground run-up.  Refer to Section 71-01. 

%

Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
77-41-00
Engine Indicating
AMM

% 3. Replace a Manifold Temperature Sensor %
%
%

%
%
%

%
%
%
%

%
%
%

%

%
%
%

%
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 6(9)