Doc # 6.02.01 Page 213
76-02-00
DA 40 Series AMM
DA 40 F
4. Throttle/Mixture Control Range of Movement Test
These procedures tell you how to do a throttle and mixture control range of movement test. They do not tell you how to adjust the engine fuel control units. Refer to the Lycoming Maintenance Manual for data on the engine fuel control units.
Do the throttle/mixture control range of movement test using two persons. You must make sure that the throttle/mixture control levers hit the stops in the throttle/mixture valve before they hit their stops in the engine control assembly. This will make sure that the throttle/mixture controls have the correct range of movement. You should set the controls to 3 mm (0.125 in) clearance (bounce) at the engine control assembly cover plate.
A. Throttle Control Range of Movement Test
Detail Steps/Work Items Key Items/References
WARNING: DO NOT STAND WITHIN THE DANGER AREA OF THE PROPELLER IF THE ENGINE STARTS, THE PROPELLER CAN CAUSE DEATH OR INJURY TO PERSONS. WARNING: YOU MUST MAKE SURE THAT THE ENGINE IS SAFE BEFORE YOU DO WORK ON THE ENGINE CONTROLS. IF THE PROPELLER TURNS IT CAN CAUSE INJURY TO PERSONS.
(1) Make sure that the engine is safe: S Set the ignition switch to OFF. S set the throttle to IDLE. S Set the mixture control to LEAN CUT-OFF
(2) Remove the engine cowlings. Refer to Section 71-12.
(3) Disconnect the airplane battery. Refer to Section 24-31.
(4) Disconnect the spark plug cables from the spark plugs.
(5) Move the throttle control lever between IDLE and FULL. S Make sure the lever moves freely with no restrictions.
DA 40 Series AMM
DA 40 F
Detail Steps/Work Items Key Items/References
(6) Set the throttle control lever to FULL and hold it in position. S Make sure that the throttle lever at the carburetor hits the stop. If necessary, adjust the Bowden cable outer sheath at the support bracket at the bottom of the engine. With the throttle lever on the stop at the carburetor, there must be at least 3 mm (0.125 in) clearance (bounce) between the lever in the engine control assembly and the cover plate.
(7) Set the throttle control lever to IDLE and hold it in position: S Make sure that the throttle lever at the carburetor hits the IDLE stop. If necessary, adjust the Bowden cable outer sheath at the engine controls bracket at carburetor. With the throttle lever on the IDLE stop at the carburetor, there must be at least 3 mm (0.125 in) clearance (bounce) between the lever in the engine control assembly and the cover plate.
(8) Move the throttle control lever between IDLE and FULL: S Make sure that the lever moves freely with no restriction.
(9) Do items 6 to 8 again as necessary to get the correct values.
(10) Do an inspection of the control connections which you disconnected. If necessary for your airworthiness authority, do a second inspection of the controls.
(11) Install the cables to the spark plugs. Torque to 12.4 to 13.6 Nm (110 - 120 in.lb).
(12) Connect the airplane battery. Refer to Section 24-31.
(13) Install the engine cowlings. Refer to Section 71-12.
(14) Do an engine test. Refer to the DA 40 F Airplane Flight Manual.
Doc # 6.02.01 Page 215
76-02-00
DA 40 Series AMM
B. Mixture Control Range of Movement Test Doc # 6.02.01 Page 217
DA 40 F
Detail Steps/Work Items Key Items/References
WARNING: DO NOT STAND WITHIN THE DANGER AREA OF THE PROPELLER IF THE ENGINE STARTS, THE PROPELLER CAN CAUSE DEATH OR INJURY TO PERSONS. WARNING: YOU MUST MAKE SURE THAT THE ENGINE IS SAFE BEFORE YOU DO WORK ON THE ENGINE CONTROLS. IF THE PROPELLER TURNS IT CAN CAUSE INJURY TO PERSONS.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 6(76)
