钻石40飞机维护手册 DA 40 SERIES AMM 6(50)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(9)  Disconnect the propeller control cable, at the propeller governor: S Loosen the nut and bolt which attaches the cable wire end to the governor. S Pull the cable wire end out of the bolt. 
(10)  Release the propeller control cable from the support bracket at the propeller governor: S Remove the front adjusting nut and washer. S Move the cable clear of the support bracket. S Remove the rear adjusting nut and washer. 
(11)  Move the propeller control cable aft through the rubber grommets in the engine cooling baffles.  Move the propeller control cable clear of the engine. 
(12)  Remove the propeller (if necessary).  Refer to Section 61-02. 
(13)  Disconnect the mixture control eye end at the engine mixture lever: S Remove the nut and washer from the long bolt at the mixture lever. S Remove the mixture cable eye end from the lever. S Remove the spacer and the long bolt. 

71-02-00
DA 40 Series AMM

DA 40 F

Detail Steps/Work Items  Key Items/References 
(14)  Remove the eye end from the control cable: S Release the lock-nut. S Remove the eye-end fitting and lock-nut from the cable. 
(15)  Release the mixture cable from the support bracket at the front of the engine: S Remove the bottom adjustment nut and washer from the control cable. S Move the control cable clear of the bracket. S Remove the top adjustment nut and washer from the control cable. 
(16)  Move the cable up and rearwards through the rubber grommets in the engine baffles.  Move the mixture cable clear of the engine. 
(17)  Disconnect the throttle cable at the carburetor: S Remove the nut and washer from the attachment bolt. S Remove the eye end from the bolt. S Remove the bolt and washer from the throttle lever at the carburetor. 
(18)  Remove the eye end from the control cable: S Loosen the lock-nut. S Remove the eye end and lock-nut. 
(19)  Remove the control cable from the bracket at the bottom of the engine: S Remove the front adjustment nut and washer from the outer sheath. S Move the control cable clear of the bracket. 
(20)  Move the throttle cable clear of the engine. 

DA 40 Series AMM

DA 40 F

Detail Steps/Work Items  Key Items/References 
(21)  Disconnect the alternate air control cable: S Release the screw which attaches the cable wire end to the swivel in the alternate air assembly. S Remove the lock-nut which holds the Bowden cable outer sheath in the support bracket at the alternate air assembly. S Move the Bowden-cable clear of the engine mount. 
WARNING: DO NOT GET FUEL ON YOU. FUEL CAN CAUSE SKIN DISEASE. DO NOT ALLOW FIRE NEAR FUEL. FUEL BURNS AND CAN CAUSE INJURY TO PEOPLE AND DAMAGE TO EQUIPMENT. 
(22)  Disconnect the fuel feed hose at the firewall.  Use a suitable container to catch the fuel. Put caps on the hose and the firewall connector. 
(23)  Release the P-clamp which attaches the breather pipe to the firewall.  Put caps on the breather pipe. 
(24)  Disconnect the two oil hoses connecting the engine oil system to the oil filter housing.  Put caps on the oil filter housing and the oil hoses. 
WARNING: DO NOT GET OIL ON YOU. OIL CAN CAUSE SKIN DISEASE. 
(25)  Disconnect the electrical connector for the oil pressure sensor and remove the cable ties which attach the electrical cable to the engine mount.  Note the position of the cable ties. 
(26)  Disconnect the cylinder-head temperature probe: S Disconnect the electrical cables for the probe. S Remove the cable ties which attach the electrical cable for the probe to the engine mount.  Do this item for each cylinder-head temperature probe. At the in-line connector. Note the position of the cable-ties. 

Doc # 6.02.01 Page 227
71-02-00
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 6(50)