20-42-21 Page 4
R Solder Sleeves - P/N Characteristics and Shrinking Tools E0160 Figure 003
20-42-21 Page 520-42-21 Page 6
R C. NSA937790
R (1) Characteristics
R (a) P/N identification
R
R NSA937790 - 03
R | |-------------------------- Size code
R |
R |----------------------------------- Standard P/N
R (b) Temperature
R Maximum operating temperature is 260 deg.C (500.00 deg.F).
R Only use this temperature on nickel-plated braided cables which
R can be continously used at 200 deg.C (392.00 deg.F) or more and
R at 400 deg.C (752.00 deg.F) for a period of 10 minutes minimum.
R (2) Installation
R (a) Wire stripping
R Refer to Method A or D Procedure.
R (b) Shrinking tools
R (Ref. Fig. 004)
R (c) Procedure
R Refer to Method A or D Procedure.
____________________________________________3. Wire Stripping Procedure (method "A" to "G")
A. Method "A" (Ref. Fig. : Method "A")
(1) Strip the bonding wire to the length A (detail A1)
(2) Make a circular cut at a distance L (detail A1).
(3) Remove the insulation.
(4) Unwind the braid (detail A2).
(5) Cut the braid to get the length B (detail A3).
B. Method "B" (Ref. Fig. : Method "B")
(1) Strip the bonding wire to the length A (detail B1)
(2) Make a circular cut at a distance L (detail B1).
R Solder Sleeves - P/N Characteristics and Shrinking Tools NSA937790 Figure 004
20-42-21 Page 7
(3)
Remove the insulation.
(4)
Cut and remove the braid (detail B2).
(5)
Make a circular cut at a distance C (detail B2).
(6)
Move the external insulation to get the length B (detail B3).
C. Method "C" (Ref. Fig. : Method "C")
(1)
Strip the bonding wire to the length A (detail C1)
(2)
Make a circular cut at a distance L (detail C1).
(3)
Remove the cable insulation.
(4)
Cut and remove the braid to get the length B (detail C2).
D. Method "D" (Ref. Fig. : Method "D")
(1)
Strip the bonding wire to the length A (detail D1)
(2)
Make a circular cut at a distance L (detail D1).
(3)
Remove the insulation.
(4)
Cut and remove the braid to get the length B (detail D2).
(5)
Move the braid rearward on the insulation (detail D3).
E. Method "E" (Ref. Fig. : Method "E")
(1)
Strip the bonding wire to the length A (detail E1)
(2)
Make three circular cuts to get the dimension L (detail E1).
(3)
Make a longitudinal cut and remove the insulation (detail E2).
F. Method "F" (Ref. Fig. : Method "F")
(1)
Strip the bonding wire to the length A (detail F1)
(2)
If necessary, install the rear mount connector on the wire (detail F2).
(3)
Install the shrinkable sleeve on the wire (detail F2).
20-42-21 Page 8
Apr 01/05
R
(4)
Install the ferrule on the wire (detail F2).
(5)
Cut and remove the insulation and the braid to get the dimension L (detail F3).
(6)
Unwind the polyimide tape (detail F3).
(7)
Remove the packing (detail F3).
(8)
Make a circular cut at a distance C (detail F3).
(9)
Move the external insulation to get the dimension D (detail F4).
(10)
Wires HG are made with UD and XM wires.
To install solder sleeves for these wires refer to :
-
Method "A" for UD wire
-
Method "C" for XM wire.
G.
Method "G" (Ref. Fig. : Method "G")
(1)
Strip the bonding wires to the lengths A and B (detail G1).
(2)
Cut the insulation and the braid to get the different dimensions (detail G1).
20-42-21 Page 9
Apr 01/05
R
R _____________________________________________4. Installation Procedure (method "A" to "G") |p
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 2(92)
