(2)
Install the correct crimping head in the power unit and screw the collar tight.
(3)
Cycle the tool twice, tightening the collar after each cycle to insure that the head is in the proper position for crimping.
(4)
Place stripped wire into a contact and insert into the locator.
(5)
Depress either the foot or hand valve to crimp. The tool
automatically makes a full cycle crimp.
20-25-24 Page 3
CANNON Crimping Tool
Model CBT600 and CBT600B
Figure 002
20-25-24 Page 420-25-24 Page 5
R _________________________________4. AMP Pneumatic Hand Tool P/N 69365
R R A. Designation (Ref. Fig. 003) This tool has interchangeable dies or jaws and uses a compressed air source (6 or 7 bars). An attachment system enables use at a fixed station, using a foot switch. In this case, the hand valve is inoperative.
B. Example of Crimping
(1) With tool equipped with proper die set for the terminal and wire size being used, proceed as follows :
(a) Insert stripped wire in terminal.
(b) Slightly lower locator.
(c) Position terminal against fixed die.
(d) Apply pressure so that moving die advances to complete the crimp. At end of crimping operation, the die automatically returns to the open position. Remove the crimped assembly.
R ___________________________________________5. DANIELS Pneumatic Crimping Tool WA27-309-EP
R R R R A. Designation (Ref. Fig. 004) This tool has a full cycle ratcheting control mechanism and uses a compressed air source (5 to 8 bars)
R B. Example of crimping
R (1) With tool in full operating condition, insert contact and wire.
R (2) Depress foot valve and hold momentarily while tool crimps.
R (3) Release to complete tool cycle.
Pneumatic Hand Tool
AMP P/N 69365
Figure 003
20-25-24 Page 6
R Pneumatic Crimping Tool - DANIELS R WA27-309-EP R Figure 004
20-25-24 Page 7
________________________________________________________
MISCELLANEOUS CRIMPING TOOLS - DESCRIPTION AND OPERATION
_______________________
1. List of Described Tools
-
AMP Hydraulic Foot Pump P/N 781019 or 69064
-
AMP Electric/Hydraulic Crimping Machine P/N 69120
___________________________________________
2. AMP Hydraulic Foot Pump P/N 781019 or 69064 (Ref. Fig. 001) Hydraulic foot pumps P/N 781019 or 69064 are used for crimping of splices, connections and terminals listed below. High temperature parallel splices. High temperature wire splices. Termalum butt splices, for aluminum RB wire. Stratotherm flag terminal. Copalum terminal.
A. Preparation of Tool
(1)
Place foot pump in a vertical position with dipstick nut uppermost.
(2)
Remove dipstick.
(3)
Check that oil level corresponds with notch on dipstick, top up oil level if necessary.
(4)
Install dipstick and place tool in horizontal position.
B. Example of Crimping
____
NOTE : : Always use tool in horizontal position.
(1)
Remove cap from crimping head adapter.
(2)
Slowly pump foot pedal until oil appears at end of hose.
(3)
Connect crimping head to hose adapter
(Ref. Fig. 002)
(4)
Install dies in crimping head.
(5)
Place terminal or splice in dies.
(6)
Lift reset pedal then return to down position.
(7)
Pump foot pedal until terminal or splice is lightly held in position in dies.
20-25-29 Page 1
Hydraulic Foot Pump
P/N 781019 or 69064
Figure 001
20-25-29 Page 2
Crimping Heads
P/N 69051, 69066 and 69099
Figure 002
20-25-29 Page 3
(8)
Insert stripped end of wire into terminal or splice.
(9)
Pump foot pedal until by-pass valve opens and the ram returns to neutral position.
(10) Open crimping head and remove terminal or splice. Before processing each crimp, press reset handle fully down and repeat foregoing steps. When last crimp is completed, release pressure and remove crimping head. Install caps on crimping head and hose.
_________________________________________________3. AMP Electric/Hydraulic Crimping Machine P/N 69120
A. Designation AMP electric/hydraulic crimping machine P/N 69120 is used for crimping:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 2(2)
