Wire Protection Tool - Protection Installation Tool Procedure
ROUNDIT 5-19
Figure 003
20-25-52 Page 6
Apr 01/04
R __________________________________4. Convoluted Conduit Connection Tool
A. General The convoluted conduit connection tool is used to install a nipple on the convoluted conduit to connect it at the rear of a connector; These nipples or end pieces have the following codes: E0074 and E0109, straight. E0075, straight for convoluted conduit with braid sheath. E0115, right angle.
B. Description of the Tool
(Ref. Fig. 004)
The size of the tool depends on the size of the conduit.
----------------------------------------------------------------------------| CONDUIT SIZE | TOOL | | |-------------------------------------------------| | CODE | MANUFACTURER | TOOL REFERENCE | |------------------------|---------------------------|---------------------| | 06 | | 16-0160-12 | |------------------------| |---------------------| | 09 | | 16-0161-12 | |------------------------| |---------------------| | 10 | | 16-0162-12 | |------------------------| |---------------------| | 12 | | 16-0163-12 | |------------------------| ICORE/ISOFLEX |---------------------| | 14 | | 16-0164-12 | |------------------------| |---------------------| | 16 | | 16-0165-12 | |------------------------| |---------------------| | 20 | | 16-0166-12 | |------------------------| |---------------------| | 24 | | 16-0167-12 | ----------------------------------------------------------------------------
C. Procedure
(Ref. Fig. 005)
-Cut the convoluted conduit to length. The cut must be clean, no tear is authorized.
-Push the connector nut and the outer ring along the conduit, observing the installation direction (step 1).
-Select the applicable tool. Put the tool end side A (the conical end) inside the convoluted conduit to flare it (step 2).
-Put the inner ring to side B of the tool; use the tool to insert the inner ring up to the shoulder into the flared conduit end (the cone on the inner ring must point to the conduit end (step 3)).
-Remove the tool; the inner ring must remain in the conduit.
20-25-52 Page 7
Apr 01/04
R
Wire Protection Tools - Convoluted Conduit Connection Tool Description
ICORE/ISOFLEX 16-016X-12 Type
Figure 004
20-25-52 Page 8
Apr 01/04
R
Wire Protection Tools - Convoluted Conduit Connection Tool Procedure
ICORE/ISOFLEX 16-016X-12 Type
Figure 005
20-25-52 Page 9
Apr 01/04
R
-Use tool side A to properly flange the protruding conduit end to the inside (step 4).
-Push the outer ring and the connector nut forward and screw them to the nipple or angle piece (step 5).
20-25-52 Page 10
Apr 01/04
R
___________________________________
5. Conduit Expansion Tool ICORE 16-987
A. General The conduit expansion tool is used to adapt the diameter of convoluted conduits to the diameter of backshells, end pieces and conduit fittings that have to be installed.
B. Description of tool (Ref. Fig. 006) Several sizes of end bit can be selected depending on the size of the convoluted conduit.
C. Procedure
-Select the correct end bit depending on the conduit size by rotating the head of the tool.
-Insert the selected end bit in the end of the conduit.
-Press the tool until the diameter of the conduit is correct.
-Extract the tool from the conduit.
20-25-52 Page 11
Apr 01/04
R
Wire Protection Tool - Conduit Expansion Tool
ICORE 16-987
Figure 006
20-25-52 Page 12
Apr 01/04
R _______________________________________________6. Hydraulic/Pneumatic Crimping Tool ICORE 16-0803
A. Designation
R (Ref. Fig. 007) ICORE hydraulic/pneumatic crimping tool ICORE 16-0803 is used for crimping sleeves on backshells, end pieces and conduit fittings. Power is controlled by a foot switch.
B. Die table -------------------------------------------------------------------------------| | | CHECK DIMENSIONS | | | |------------------------------------------| | CONDUIT SIZE | DIE ICORE P/N | DIAMETER OF OPENING |MAX. SLEEVE DIAMETER| | | | FOR SECOND CRIMP | AFTER CRIMPING * | | | | OPERATION mm (in.) | mm (in.) | |------------------|---------------|---------------------|--------------------| | VW-06 | V-06 | 16-1227-06 | 10.11 (0.3980) | 10.26 (0.4039) | |---------|--------|---------------|---------------------|--------------------| | VW-09 | V-09 | 16-1227-09 | 12.50 (0.4921) | 12.65 (0.4980) | |---------|--------|---------------|---------------------|--------------------| | VW-10 | V-10 | 16-1227-10 | 13.40 (0.5275) | 13.55 (0.5334) | |---------|--------|---------------|---------------------|--------------------| | VW-12 | V-12 | 16-1227-12 | 15.40 (0.6062) | 15.55 (0.6122) | |---------|--------|---------------|---------------------|--------------------| | VW-14 | V-14 | 16-1227-14 | 16.96 (0.6677) | 17.11 (0.6736) | |---------|--------|---------------|---------------------|--------------------| | VW-16 | V-16 | 16-1227-16 | 18.61 (0.7326) | 18.76 (0.7385) | |---------|--------|---------------|---------------------|--------------------| | VW-20 | V-20 | 16-1227-20 | 21.76 (0.8566) | 21.91 (0.8625) | |---------|--------|---------------|---------------------|--------------------| | VW-24 | V-24 | 16-1227-24 | 25.73 (1.0129) | 25.88 (1.0188) | |---------|--------|---------------|---------------------|--------------------| | VW-32 | V-32 | 16-1227-32/1 | 33.42 (1.3157) | 33.57 (1.3216) | | | | 16-1227-32/2 | | | -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 2(11)
