-
Install the fairlead on the support.
-Hold this assembly with serflex adjustable clamp ASNA0033 or cable tie NSA935401.
20-33-41 Page 23
R Cable Supports - Fairlead Guide Type Installation R ABS0678 with ABS0679 and NSA935512 Figure 012
20-33-41 Page 2420-33-41 Page 25
_________________________6. Separator and Spacer Type
This type of cable support has the codes that follow: ABS0054
ABS0731
E0688
NSA5527
R R R R R R You can use these types of cable supports to keep the electrical wiring separate. When their use is mandatory, they are shown in the installation drawing. If necessary, you can add spacers to get a correct clearance but you must keep them to a minimum.
R R This type of cable support is used in all areas except hot areas. In these areas, lacing tape NSA8420-2 is used as separator (noose type knot).
R ____NOTE : For EFCS harnesses, the use of spacers or separators is prohibited.
R
R A. P/N Characteristics (Ref. Fig. 013)
(1) P/N identification NSA5527 -03-02 -D
ABS0054 A 5
ABS0731 A 01
E0688 01
| | | | | --- Size code (For ABS0054 and ABS0731) | | or | | Material code (For NSA5527) | Without code : PA 6.6 | | | D code : ALU | | | -----------Size code (For E0688 and NSA5527) | or | Color and material code (For ABS0054 and ABS0731): | A= PA 6.6 natural color | ------------------------Standard P/N
(2) Temperature - For ABS0054:
Minimum operating temperature is : -40 deg.C (-40.00 deg.F). Maximum operating temperature is : 85 deg.C (185.00 deg.F). - For ABS0731:
Minimum operating temperature is : -55 deg.C (-67.00 deg.F).
R Cable Supports - Separator and Spacer Type Description ABS0054, ABS0731, E0688 and NSA5527 Figure 013
20-33-41 Page 26
Maximum operating temperature is : 135 deg.C (275.00 deg.F).
-
For E0688: Minimum operating temperature is : -40 deg.C (-40.00 deg.F). Maximum operating temperature is : 105 deg.C (221.00 deg.F).
-
For NSA5527: Maximum operating temperature is : 130 deg.C (266.00 deg.F).
(3) Dimensional characteristics R (Ref. Fig. 014)
20-33-41 Page 27
Cable Supports - Separator and Spacer Type Characteristics
ABS0054, ABS0731, E0688, NSA5527 and NSA935510
Figure 014
20-33-41 Page 28
Apr 01/02
R
B. Procedure R (Ref. Fig. 015, 016)
-Select the applicable separator or spacer type.
____NOTE : On flight control circuits you must not use spacers or separators.
-Hold the bundles on the separator or spacer with cable tie NSA935401 (Obey a minimum distance).
20-33-41 Page 29
R Cable Supports - Separator and Spacer Type Installation ABS0054, ABS0731, E0688, NSA5527 and NSA935510 Figure 015
20-33-41 Page 30
R Cable Supports - Separator and spacer Type Installation R ABS0054, ABS0731, E0688, NSA5527 and NSA935510 R Figure 016
20-33-41 Page 31
______________
7. Specific cases R (Ref. Fig. 017)
In some cases (for example in VU, interface areas...) the structure (colonnette) or ramp is used to support the wiring to make sure that:
-it is not pinched during the VU installation in position in the aircraft, or
-rubbing does not occur during the life of the aircraft. To be approved, the structure or ramps which are metallic must have a protection of special paint (for the ramp) or a heat shrinkable sleeve (for the colonnette).
20-33-41 Page 32
Cable Supports - Special Cases R Figure 017
20-33-41 Page 3320-33-42 Page 1
__________________________________CLAMPS - DESCRIPTION AND OPERATION
_______1. General
This chapter gives the description and operation for clamps. The clamps are
items used to attach the wiring.
A very wide range of clamps and mounts are used.
R The main clamps installed on aircraft have the codes that follow :
R - ABS1339 protected nylon clamp
R - NSA5515 non protected nylon clamp
- NSA5516 or MS21919 protected clamps
- NSA935807 "P" clamp for convoluted conduit.
___________2. Description
R A. ABS1339 protected nylon clamp type
R (Ref. Fig. 001)
R (1) P/N identification
R ABS1339 D 01
R | | |
R | | ----------- Size code
R | |
R | ---------------- Variant code | D = brown (general use)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 2(70)
