-
the fuel sensors 15QJ1(15QJ2), 23QJ1(23QJ2) and 24QJ1(24QJ2).
(b)
Disconnect the terminal connectors (2) from the terminal block of the fuel probes 22QT1(22QT2), 24QT1(24QT2) and 26QT1(26QT2).
(c)
Remove and discard the terminal connectors (2) from the ends of the harness 14QT1(14QT2).
(d)
Loosen the clamp screws (21), the connector screws (20) and remove the cables from the sensors 15QJ1(15QJ2), 23QJ1(23QJ2) and 24QJ1(24QJ2).
(e)
Remove and discard the cable-ties (1) from the harness 14QT1(14QT2) and the fuel probes 22QT1(22QT2), 24QT1(24QT2) and 26QT1(26QT2).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 443 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Electrical Harness 14QT1(14QT2) at RIBS 2 and 9, and at STRGR 11
-Location and Detail
Figure 406/TASK 28-42-43-991-011
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 444 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Electrical Harness 14QT1(14QT2) at RIBS 3, 7, 11, and 13 - Location and Detail
Figure 407/TASK 28-42-43-991-010
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 445 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(f)
Remove the bolt (4) to release the P clip (3).
(g)
Remove the harness 14QT1(14QT2) from the P clip (3) and use the bolt (4) to temporarily install the P clip (3).
(h)
Loosen the clamp screws (21), the connector screws (20) and remove the cable from the sensor 39QJ1(39QJ2).
(i)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2).
(2) Remove the harness 14QT1 (14QT2) at RIB 7 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 404/TASK 28-42-43-991-007, 405/TASK 28-42-43-991-009)
WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK.
_______
LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(a)
Get access through the opening 574BB(674BB).
(b)
Disconnect the plug connector (33) from the connector
4040VC1(4040VC2) (34).
(c)
Put a blanking cap on the plug connector (33).
(d)
Remove and discard the lockwire from the nut (32).
(e)
Remove the nut (32) and the washer (31) from the connector (34).
(f)
Get access through the opening 540BB(640BB) to the rear spar.
(g)
Use a plastic spatula to remove the sealant from between the connector (34) and the tank wall.
(h)
Remove the connector (34) and discard the O-ring (30).
(i)
Remove and discard the lockwire and loosen the clamp screws (36).
(j)
Remove and discard the lockwire from the backshell connector (35).
(k)
Remove the backshell connector (35) from the connector (34).
(l)
Retain the backshell connector (35) and the connector (34).
(m)
Remove the bolt (4) from the P clip (3), then remove and retain the P clip (3).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-42-43Page 446 1201-228, 1May 01/05 1 1 1CES 1
(n)
Disconnect the terminal connectors (2) from the fuel probe 28QT1(28QT2).
(o)
Remove and discard the terminal connectors (2) from the terminal block of the harness 14QT1(14QT2).
(p)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2) and the fuel probe 28QT1(28QT2) body.
(3)
Remove the harness 14QT1 (14QT2) at RIB 9 as follows: (Ref. Fig. 406/TASK 28-42-43-991-011)
(a)
Get access through the opening 540CB(640CB).
(b)
Loosen the clamp scew (21), the connector screws (20) and remove the cable from the sensor 25QJ1(25QJ2).
(c)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2).
(4)
Remove the harness 14QT1 (14QT2) at RIB 11 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 407/TASK 28-42-43-991-010)
(a)
Get access through the opening 540FB(640FB).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油5(96)
