(c)
Connect the terminal connectors (2) to the terminals of the terminal block of the fuel probe 25QT1(25QT2).
(d)
Put the cable for the fuel probe 25QT1(25QT2) in position.
(e)
Attach the harness 13QT1(13QT2) to the fuel probe 25QT1(25QT2) body and the structure with the cable-ties (1).
(f)
Identify the cable ends for the fuel probe 23QT1(23QT2).
(g)
Use a crimping tool to crimp the correct color terminal R connectors (2) to the color identified wires (Ref. ESPM 203222).
(h)
Connect the terminal connectors (2) to the terminals of the terminal block of the fuel probe 23QT1(23QT2).
(i)
Put the cable for the fuel probe 23QT1(23QT2) in position.
(j)
Attach the harness 13QT1(13QT2) to the structure with the cable-ties (1).
(k)
Identify the cable ends for the sensors 16QJ1(16QJ2), 29QJ1(29QJ2) and 38QJ1(38QJ2).
(l)
Connect the applicable cable to the sensors 16QJ1(16QJ2), 29QJ1(29QJ2) and 38QJ1(38QJ2) with the screws (20).
(m)
Put each cable in the clamp (22) and tighten the screws (21).
(n)
Put the cable for the sensors 16QJ1(16QJ2), 29QJ1(29QJ2) and 38QJ1(38QJ2) in position.
(o)
Attach the harness 13QT1(13QT2) to the structure with the cable-ties (1).
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 432 1 1 Aug 01/05 1 1 1CES 1
(p) Install the nylon spacers (5) between the applicable harnesses with the cable-ties (1).
NOTE : Make sure that there is not less than 6mm (0.24in.)
____ between the cables of the sensors 29QJ1(29QJ2) and 38QJ1(38QJ2), and the fuel probe 24QT1(24QT2).
(q)
Remove the bolt (4) and the P clip (3).
(r)
Make a coil of the unwanted cable and use the P clip (3) and the bolt (4) to attach it to the structure.
(3) Install the harness 13QT1 (13QT2) at RIB 1 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 403A/TASK 28-42-43-991-006-A)
(a)
Identify the cable for the fuel probe 21QT1(21QT2) and put it through the RIB2 in the position shown.
(b)
Get access through the opening 540AB(640AB) and the door 540AZ(640AZ) to the RIB1.
(c)
Carefully pull the cable for the fuel probe 21QT1(21QT2) until it reaches the fuel probe.
(d)
Remove the tape and the string from the harness 13QT1(13QT2).
(e)
Identify the cable ends for the fuel probe 21QT1(21QT2).
(f) Use a crimping tool to crimp the correct color terminal R connectors (2) to the color identified wires (Ref. ESPM 203222).
(g)
Connect the terminal connectors (2) to the terminals of the terminal block of the fuel probe 21QT1(21QT2).
(h)
Put the cable for the fuel probe 21QT1(21QT2) in position.
(i)
Attach the harness 13QT1(13QT2) to the fuel probe 21QT1(21QT2) body and the structure with the cable-ties (1).
(j)
Get access through the opening 540BB(640BB) to RIB6 and through the openings in RIB4 and RIB5.
(k)
Carefully pull the string for the cable for the fuel probe 27QT1(27QT2) until it comes into view at the end of the conduit.
(l)
Remove and discard the tape and the string from the harness.
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 433 1 1 Aug 01/05 1 1 1CES 1
(4) Install the harness 13QT1 (13QT2) at RIB 6 as follows: (Ref. Fig. 405/TASK 28-42-43-991-009)
(a) Identify the cable ends for the fuel probe 27QT1(27QT2).
(b)
Use a crimping tool to crimp the correct color terminal R connectors (2) to the color identified wires (Ref. ESPM 203222).
(c)
Connect the terminal connectors (2) to the terminals of the terminal block of the fuel probe 27QT1(27QT2).
(d)
Put the cable for the fuel probe 27QT1(27QT2) in position.
(e)
Attach the harness 13QT1(13QT2) to the fuel probe 27QT1(27QT2) body and the structure with the cable-ties (1).
(f)
Get access through the opening 540CB(640CB) to RIB9.
(g)
Carefully pull the string for the cable for the fuel probe 29QT1(29QT2) until the cable comes into view, at the end of the conduit.
(h)
Remove and discard the tape and the string from the harness.
中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FUEL 燃油5(92)
