(b)
Disconnect the plug connector (33) from the connector
4039VC1(4039VC2) (34).
(c)
Put a blanking cap on the plug connector (33).
(d)
Remove and discard the lockwire from the nut (32).
(e)
Remove the nut (32) and the washer (31) from the connector (34).
(f)
Get access through the opening 540BB (640BB) to the rear spar.
(g)
Use a plastic spatula to remove the sealant from between the connector (34) and the tank wall.
(h)
Remove the connector (34) and discard the O-ring (30).
(i)
Remove and discard the lockwire and loosen the clamp screws (36).
(j)
Remove and discard the lockwire from the backshell connector (35).
(k)
Remove the backshell connector (35) from the connector (34).
(l)
Retain the backshell connector (35) and the connector (34).
(m)
Remove the bolt (4) from the P clip (3), then remove and keep the P clip (3).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-42-43Page 408 1201-228, 1May 01/05 1 1 1CES 1
Electrical Harness 13QT1(13QT2) at RIBS 1 and 2 - Location and Detail Figure 403A/TASK 28-42-43-991-006-A
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 409 1 1 Aug 01/05 1 1 1CES 1
Electrical Harness 13QT1(13QT2) and 14QT1(14QT2) at RIBS 2, 2/3, 6/7 and 9
-Location and Detail
Figure 404/TASK 28-42-43-991-007
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 410 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(4)
Remove the harness 13QT1 (13QT2) at RIB 9 as follows: (Ref. Fig. 404/TASK 28-42-43-991-007, 405/TASK 28-42-43-991-009)
(a)
Get access through the opening 540DB(640DB).
(b)
Disconnect the terminal connectors (2) from the terminal block of the fuel probe 29QT1(29QT2).
(c)
Remove and discard the terminal connectors (2) from the end of the harness.
(d)
Remove and discard the cable-ties (1) from the harness
13QT1(13QT2) and the fuel probe 29QT1(29QT2).
(5)
Remove the harness 13QT1 (13QT2) at RIB 13 as follows: (Ref. Fig. 405/TASK 28-42-43-991-009)
(a)
Get access through the opening 540GB(640GB).
(b)
Disconnect the terminal connectors (2) from the terminal block of the fuel probe 31QT1(31QT2).
(c)
Remove and discard the terminal connectors (2) from the ends of the harness.
(d)
Loosen the clamp screws (21), the connector screws (20) and remove the cable from the sensor 17QJ1(17QJ2).
(e)
Remove and discard the cable-ties (1) from the harness
13QT1(13QT2).
(6)
Remove the harness 13QT1 (13QT2) inboard of RIB 15 as follows: (Ref. Fig. 405/TASK 28-42-43-991-009)
(a)
Get access through the opening 540JB(640JB).
(b)
Disconnect the plug connector (33) from the connector
4045VC1(4045VC2) (34).
(c)
Put a blanking cap on the plug connector (33).
(d)
Remove the bolts (43), the nuts (45) and the anti-rotation plate (44).
(e)
Remove and discard the lockwire from the nut (32).
(f)
Remove the nut (32) and the washer (31) from the connector (34).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-42-43Page 411 1201-228, 1May 01/05 1 1 1CES 1
Electrical Harness 13QT1(13QT2) and 14QT1(14QT2) at RIBS 6, 13 and 15
and at the Rear Spar - Detail and Location
Figure 405/TASK 28-42-43-991-009
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 412 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(g) Get access through the opening 540KB(640KB).
(7)
Remove the harness 13QT1 (13QT2) ouboard of RIB 15 as follows: (Ref. Fig. 405/TASK 28-42-43-991-009)
(a)
Use a plastic spatula to remove the sealant from between the connector (34) and the tank wall.
(b)
Remove the connector (34) from the rib mounting and discard the O-ring (30).
(c)
Remove and discard the lockwire and loosen the clamp screws (36).
(d)
Remove and discard the lockwire from the backshell connector (35).
(e)
Remove the backshell connector (35) from the plug connector (34) and retain the backshell connector (35).
(f)
Remove and discard the connector pins from the wires of the connector (34).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油5(84)
