EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-62-21
ALL ú ú 03 Page 402 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
C. Prepare for FMCS BITE Test
S 864-042
(1)
Supply electrical power (AMM 24-22-00/201).
S 864-043
(2)
Make sure the BAT switch on the Pilot's Forward Overhead Panel is in the ON position.
S 864-044
(3)
Set the STANDBY POWER switch on the Pilot's Forward Overhead Panel to the AUTO position.
S 864-045
(4)
Make sure the LANDING GEAR AIR/GND RELAY & LIGHTS circuit breaker on the P6 panel is closed.
S 864-046
(5)
Use the Master Dim and Test switch to make sure the indicator lamps and annunciator lights operate correctly.
S 864-047
(6)
Make sure these circuit breakers are closed:
(a) P18 Panel
1) CDU No. 1
2) CDU No. 2 (when installed)
NOTE: On airplanes with provisions for dual FMC, FMCS CDU
____ (ANCDU, MCDU) No. 2 circuit breaker will be on the P6-1 panel.
3) FMC (or FMCS CMPTR)
4) MODE ANN
(b) AIRPLANES WITH DUAL FMC;
P6-1 panel
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-62-21
ALL ú ú 10 Page 403 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
1) FMCS CDU No. 2
2) FMCS CMPTR No. 2
3) FMCS XFER
ú D. FMC Software Check
ú
ú S 714-019
ú (1) Do these steps to examine the FMC software:
ú (a) Make sure the CDU display shows the IDENT 1/x page.
ú 1) AIRPLANES WITH FMC P/N 10-62225-XXX AND SOFTWARE UPDATE 7
ú AND SUBSEQUENT;
ú If the CDU shows OP PROGRAM INVALID, do the operational
ú program installation (AMM 34-62-01/201).
ú 2) If the CDU display does not show the IDENT 1/x page, open
ú the FMC (or FMCS CMPTR) circuit breaker on the P18 panel.
3) After 15 seconds, close the FMC (or FMCS CMPTR) circuit
breaker on the P18 panel.
ú 4) Make sure that the CDU display shows the IDENT 1/x page.
ú (b) Make sure the part numbers shown on the IDENT 1/x page for the
ú navigation data base and operational program are correct.
ú (c) Make sure the dates shown on the IDENT 1/x page, directly below
ú ACTIVE, are current.
ú (d) If the part numbers or dates are incorrect, use a data loader
ú to load the correct FMC software (AMM 34-62-00/201 or AMM
ú 34-62-01/201).
ú (e) AIRPLANES WITH FMC P/N 10-62225-XXX AND SOFTWARE UPDATE 7 AND
ú SUBSEQUENT;
ú Push the NEXT PAGE button.
ú 1) Make sure the CDU shows the IDENT 2/x page.
ú (f) AIRPLANES WITH FMC P/N 10-62225-XXX AND SOFTWARE UPDATE 7 AND
ú SUBSEQUENT;
ú Make sure the part number shown for the databases is correct.
ú
ú
NOTE: When a database is not installed the CDU shows____
ú DEFAULTXXX below the name of the database.
ú
E. Performance (PERF) Factors - Verification/Adjustment
NOTE: The performance factors are airline supplied constants. These____
constants are: PERF CODE, DRAG FACTOR, F-F (fuel flow) FACTOR,
MNVR (maneuvar) MARGIN, MIN CRZ (minimum cruise) TIME, and MIN R/C
(minimum rate of climb) CLB, CRZ and ENG OUT.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737-300 400 500 AMM 飞机维护手册 导航 NAVIGATION 5(117)