R 1EFF : 062-099, 105-149, 151-199, 204-299, 1 52-13-00Page 541 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Upper and Lower Guide Arms X axis Adjustment Figure 511/TASK 52-13-00-991-021
R 1EFF : 1 1 1CES ALL 1 111 52-13-00 Page 542 May 01/05
(d) If they are stressed do an adjustment of the the upper guide arm
(87) and lower guide arm (84) as follows:
1_ Identify the position of the serrations of the plates (82) and
(85).
2_ Loosen the nuts (81) and (89).
3_ Move the fittings (83) and (86) on the X axis to get the
correct position.
4_ Temporarily tighten the nuts (81) and (89).
(2) Adjustment on the Y axis
(a)
Open the door until the nominal axis of the guide arms and the support arms are aligned.
(b)
Make sure that the bolts (88) at the guide arm/door attachment are not stressed.
(c)
If they are stressed adjust the upper guide arm (87) and lower guide arm (84) as follows:
1 Identify the position of the serrations of the plates (82) and
_ (85).
2 Loosen the nuts (81) and (89).
_ 3 Move the fittings (83) and (86) on the Y axis to get the
_ correct position.
4 Tighten the nuts (81) and (89).
_
R 1EFF : 001-049, 051-061, 101-104, 201-203, 1 52-13-00Page 543 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-13-00-820-056-A
F. Check and Adjustment of the Upper and Lower Guide Arms
(Ref. Fig. 510A/TASK 52-13-00-991-004-A)
(1) Adjustment on the X axis.
(Ref. Fig. 511/TASK 52-13-00-991-021)
(a) For the door that has the door damper and emergency-operation cylinder P/N series FE174 and FE196.
1 Put the door in the up closed position, to touch the seal.
_
(b) For the door that has the door damper and emergency-operation cylinder P/N serie FE240.
1 Put the door in the up closed position, to touch the seal at
_
FR68.
a Do a check of the clearance J1 at FR66. The clearance J1
_ must be equal to the difference between:
-the flushness D1 measured between the door and the door frame forward of the door,
-and the flushness D2 measured between the door and the
door frame aft of the door. The maximum clearance J1 must be of 5 mm (0.1968 in.).
NOTE : Measure the clearance at door stop level L5.
____
(c)
Make sure that there is no stress on the bolts (88) at the guide arm/door attachment.
(d)
If there is stress, do an adjustment of the the upper guide arm
(87) and lower guide arm (84) as follows:
1 Identify the position of the serrations of the plates (82) and
_
(85).
2 Loosen the nuts (81) and (89).
_ 3 Move the fittings (83) and (86) on the X axis to get the
_
correct position.
R 1EFF : 062-099, 105-149, 151-199, 204-299, 1 52-13-00Page 544 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 (2) Adjustment on the Y axis
4_ Make sure that the eccentric washers (80) and (90):
- fully seal the holes of the fittings (83) and (86),
- are not above the rounded areas or spot-facing edges,
- are not out of the outer contour of the fitting.
5_ Temporarily tighten the nuts (81) and (89).
(a)
Open the door until the nominal axis of the guide arms and the support arms are aligned.
(b)
Make sure that there is no stress on the bolts (88) at the guide arm/door attachment.
(c)
If there is stress, adjust the upper guide arm (87) and lower guide arm (84) as follows:
1 Identify the position of the serrations of the plates (82) and
_
(85).
2 Loosen the nuts (81) and (89).
_ 3 Move the fittings (83) and (86) on the Y axis to get the
_
correct position.
4 Make sure that the eccentric washers (80) and (90):
_ -fully seal the holes of the fittings (83) and (86),
-are not above the rounded areas or spot-facing edges,
-are not out of the outer contour of the fitting. 5 Tighten the nuts (81) and (89).
_
**ON A/C ALL
Subtask 52-13-00-820-057
G. Adjustment of the Escape Slide and Girt Bar Fittings R **ON A/C 001-002, 051-052,
(Ref. Fig. 503/TASK 52-13-00-991-006)
1EFF : ALL 1 52-13-00Page 545 1 1 May 01/05 1 1 1CES 1
**ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 503A/TASK 52-13-00-991-006-A) **ON A/C ALL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门2(66)
