• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-26 23:42来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 61.94 lbf.in).

 (7) Installation of the locking hook (2).
 (a) Install the locking hook. 1 Put the door in the up position.
_ 2 Apply COMMON GREASE (Material No. 04-004) on the sliding part
_
 of the shouldered bush (4). 3 Install the shouldered bush (4), the bolt (15), the washer
_
 (14) and the nut (5). 4 TORQUE the nut (5) to between 1.2 and 1.35 m.daN (106.19 and
_
 119.46 lbf.in). 5 Install a new cotter pin (6).
_ NOTE : If you install a new bolt (15), drill a hole of 2.7 mm
____ (0.1062 in.) for the cotter pin installation.
 (b) Connect the rod (48). 1 Install the bellow (50), the plate (51), the bolts (52) and
_
 the clamp (53). Do not tighten the clamp (53). 2 TORQUE the nuts (49) to between 0.35 and 0.45 m.daN (30.97 and
_
 39.82 lbf.in). 3 Install the bushes (10) and (11) with SPECIAL MATERIALS
_
 (Material No. 05-002), the washer (12) and the bolt (13). 4 Install the washer (9) and the nut (8).
_ 5 TORQUE the nut (8) to between 0.7 and 0.8 m.daN (61.94 and
_ 70.79 lbf.in).
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-21Page 456 1201-207, 1May 01/05 1 1 1CES 1


 6_ Install a new cotter pin (7).
 NOTE : If you install a new bolt (13), drill a hole of 2 mm____
 (0.0787 in.) for the cotter pin installation.

 (c) Connect the rod (23). 1 Install the bushes (21) and (22) with SPECIAL MATERIALS
_
 (Material No. 05-002), the washer (17) and the bolt (16). 2 Install the washer (18) and the nut (29).
_ 3 TORQUE the nut (19) to between 0.15 and 0.17 m.daN (13.27 and
_
 15.04 lbf.in). 4 Install a new cotter pin (20).
_ NOTE : If you install a new bolt (16), drill a hole of 1.8 mm
____ (0.0708 in.) for the cotter pin installation.
 (8) Adjustment of the locking hook (2). (Ref. Fig. 415/TASK 52-13-21-991-030)
 (a)
 Open the door.

 (b)
 Put two shims in the upper fittings located on the frame.

 (c)
 Close the door and adjust the locking hook (2) as follows:


 1_ Turn the barrel of the rod (48) until you get the contact
 between the locking hook (2) and the roller (58).
 2_ Tighten the nuts (46) and the clamp (53).
 3_ Make sure that the lockwashers (47) are correctly positioned.
 4_ Safety the nuts (46) and the lockwashers (47) with

 MISCELLANEOUS (Material No. 19-010).
 (d) Open the door and remove the shims located on the upper fittings (located on the frame).
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-21Page 457 1201-207, 1May 01/05 1 1 1CES 1


 Locking Hook Adjustment
 Figure 415/TASK 52-13-21-991-030

R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-21Page 458 1201-207, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 155-199, 208-299, 301-399, 401-499,


 Subtask 52-13-21-420-055-A
 E. Installation of the Safety Pin and Locking Hook
 (Ref. Fig. 406/TASK 52-13-21-991-012)

 (1)
 Make sure that the door is open.

 (2)
 Connect the rod (33).

 (a)
 Install the bushes (34) and (39) with SPECIAL MATERIALS (Material No. 05-002), the rod (33), the washer (32) and the bolt (31).

 (b)
 Install the washer (35) and the nut (36).

 (c)
 TORQUE the nut (36) to between 0.3 and 0.35 m.daN (26.54 and

 30.97 lbf.in).

 (d)
 Install a new cotter pin (37). NOTE : If you install a new bolt (31), drill a hole of 1.9 mm

 


____ (0.0748 in.) for the cotter pin installation.
 (3) Installation of the safety pin on the fitting (56).
 (a)
 Apply COMMON GREASE (Material No. 04-004) on the sliding part of the safety pin (30).

 (b)
 Install the safety pin (30) in its fitting (56).

 (c)
 Apply SEALANTS (Material No. 09-019) on the surface of the fitting (56) in contact with the door structure.

 (d)
 Put the fitting (56) in position on the door structure and remove the unwanted sealant with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).

 (e)
 Install the washers (35) and the bolts (54) and (55). Apply SPECIAL MATERIALS (Material No. 05-002) on the thread of the bolts (54) and (55) before installation.

 (f)
 Tighten the bolts (54) and (55).


R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-21Page 459 1401-499, 1Aug 01/05 1 1 1CES 1


 (4)
 Assembly of the safety pin.

 (a)
 Install the washer (29), the caps (28) (27) and (26), the washer
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM DOORS 舱门2(124)