(11)
Apply COMMON GREASE (Material No. 04-004) on the bolt shank and install the bolt (186), the washer (185).
(12)
Install the rods (160), (184), the flexible control (168), the washers (165) and the nuts (167).
(13)
TORQUE the nuts (167) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
(14)
Install the cotter pin (166).
(15) Remove the RIGGING PIN (98DNSA20206120).
Subtask 52-11-22-420-053
E. Installation of the Escape Slide Gear Box
(Ref. Fig. 402/TASK 52-11-22-991-002)
R **ON A/C 001-002, 051-052,
(Ref. Fig. 410/TASK 52-11-22-991-013)
1EFF : ALL 1 52-11-22Page 431 1 1 May 01/05 1 1 1CES 1
Escape Slide Gearbox - Telescopic Rod Adjustment
Figure 410/TASK 52-11-22-991-013
R 1EFF : 001-002, 051-052, 1 52-11-22Page 432 1 1 May 01/05 1 1 1CES 1
**ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 410A/TASK 52-11-22-991-013-A) **ON A/C ALL
(1)
Install the escape slide gear box (51) and apply SEALANTS (Material No. 09-019) on the contact surfaces between the escape slide gear box and the door structure.
(2)
Install the washers (52), the bolts (53) and tighten them.
(3)
Install the washer (54), the bolt (55) and tighten it.
(4)
Put the inner control handle and the outer control handle in the locked down position.
(5)
Put the emergency control handle in the ARMED position.
(6)
Install a RIGGING PIN (98DNSA20206120).
(7)
Keep the contact between the cam (57) and the lower part of the roller (58).
(8)
Measure the dimension X1 when the operations above are completed.
(9)
Adjust the length of the rod (45) in the maximum extended position so that the length is equal to X1+ 0.1 +0.1 -0.1 mm (0.0039 +0.0039 -0.0039 in.).
(10)
Make sure that the clearance X2 is 0 +0.1 +1.5 mm (0.0000 +0.0039 +0.0590 in.)
(11)
Put the rod (45) in position.
(12)
Install the washers (41), (42), the bolt (40) and the nut (44).
(13)
TORQUE the nut (44) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
NOTE : If you install a new bolt (40) drill a hole of 1.9 mm (0.0748
____
in.).
(14) Install the cotter pin (43).
R 1EFF : ALL 1 52-11-22Page 433 1 1 May 01/05 1 1 1CES 1
Escape Slide Gearbox - Telescopic Rod Adjustment Figure 410A/TASK 52-11-22-991-013-A
1EFF : 1 1R 1CES ALL 1 11 1 52-11-22 Page 434 May 01/05
(15) Install the bolt (46), the washers (47), (48), the nut (50) and tighten it.
NOTE : If you install a new bolt (46), drill a hole of 2 mm (0.0787
____
in.).
(16)
Install the cotter pin (49).
(17)
Install the plate assembly (72) as follows.
(a)
Apply a coat of SEALANTS (Material No. 09-019) on the contact surface between the plate assembly and the door structure.
(b)
Put the plate assembly in position.
(c)
Install the washers (71) and the bolts (70).
(d)
Tighten the bolts (70).
(18) Remove the RIGGING PIN (98DNSA20206120).
Subtask 52-11-22-420-054
F. Installation of the Emergency Control Handle R **ON A/C 001-002, 051-052,
(Ref. Fig. 401/TASK 52-11-22-991-001) **ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 401A/TASK 52-11-22-991-001-A) **ON A/C ALL
(Ref. Fig. 409/TASK 52-11-22-991-012)
(1)
Put the bellcrank (24), the spacer (23) and the washers (22) in position.
(2)
Install the escape slide handle axle (19).
1EFF : ALL 1 52-11-22Page 435 1 1 May 01/05 1 1 1CES 1
(3)
Install the taper pin (31), the washer (6), the nut (8) and the
cotter pin (7).
(4)
Install the emergency control handle (21).
(5)
Install the taper pin (20), the washer (18), the nut (17) and the
cotter pin (16).
(6)
Install the lever (1).
(7)
Install the taper pin (2), the washer (5), the nut (4) and the cotter pin (3).
(8)
Apply COMMON GREASE (Material No. 04-004) on the sliding part of the rod (32).
(9)
Install the spring (33), the washers (39), the bush (34) and the rod (32).
(10)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门2(24)
