R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-00Page 530 1201-207, 1May 01/05 1 1 1CES 1
Adjustment of the Upper Hook of the Aft Passenger/Crew Door
Figure 508/TASK 52-13-00-991-019
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-00Page 531 1201-207, 1May 01/05 1 1 1CES 1
(f)
Open the door, remove the nuts (34), the bolts (35) and the two shims.
(g)
Adjust the thickness of the adjustable washers (33).
(h)
Install the adjustable washers (33), the bolts (35) and the nuts
(34) and tighten them.
(4)
If there is no contact at the locking hook (41), do the adjustment below:
(a)
Put the two shims in position in the upper guide fittings (32).
(b)
Close the door.
(c)
Remove and discard the lockwire from the nuts (42).
(d)
Loosen the nuts (42) and release the lockwashers (43).
(e)
Loosen the clamp (45).
(f)
Turn the barrel of the rod (44) until you get the contact between the locking hook (41) and the roller (40).
(g)
Tighten the nuts (42) and the clamp (45).
(h)
Make sure that the lockwashers (43) are correctly positioned.
(i)
Safety the nuts (42) and the lockwashers (43) with MISCELLANEOUS (Material No. 19-010).
(j)
Open the door and remove the two shims.
(5)
Make sure that when the door is closed the roller (40) turns freely.
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-00Page 532 1201-207, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 155-199, 208-299, 301-399, 401-499,
Subtask 52-13-00-820-054-A
D. Check in the Z Axis of the Door and Locking Hook Adjustment (Ref. Fig. 502A/TASK 52-13-00-991-005-A, 508A/TASK 52-13-00-991-019-A)
(1)
Close the door.
(2)
Make sure that:
(a)
The clearance C6 between the rollers (31) and the bolts (35) is
0.2 mm (0.0078 in.).
(b)
The locking hook (41) is in contact with the roller (40) and the clearance M1 is 0.5 +0.3 -0.3 mm (0.0196 +0.0118 -0.0118 in.).
(3)
If the clearance C6 is not in the tolerances, do the adjustment that follows:
(a)
Open the door.
(b)
Remove the nuts (34), the adjustable washers (33), and the bolts (35).
(c)
Install the bolts (35) and the nuts (34).
(d)
Put the two shims (thickness 0.2 mm (0.0078 in)) in position in the upper guide fittings (32).
(e)
Close the door and measure the dimension between the rollers (31) and the bolts (35).
(f)
Open the door, remove the nuts (34), the bolts (35) and the two shims.
(g)
Adjust the thickness of the adjustable washers (33).
(h)
Install the adjustable washers (33), the bolts (35) and the nuts
(34) and tighten them.
(4)
If there is no contact at the locking hook (41), do the adjustment that follows:
(a) Put the two shims in position in the upper guide fittings (32).
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-00Page 533 1401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Upper Hook of the Aft Passenger/Crew Door
Figure 508A/TASK 52-13-00-991-019-A12 (SHEET 1)
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-00Page 534 1401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Upper Hook of the Aft Passenger/Crew Door
Figure 508A/TASK 52-13-00-991-019-A22 (SHEET 2)
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-00Page 535 1401-499, 1Aug 01/05 1 1 1CES 1
(b)
Close the door.
(c)
Remove and discard the lockwire from the nuts (42).
(d)
Loosen the nuts (42) and release the lockwashers (43).
(e)
Loosen the clamp (45).
(f)
Turn the barrel of the rod (44) until the locking hook (41) touches the roller (40).
(g)
Tighten the nuts (42) and the clamp (45).
(h)
Make sure that the lockwashers (43) are correctly positioned.
(i)
Safety the nuts (42) and the lockwashers (43) with MISCELLANEOUS (Material No. 19-010).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门2(64)
