1 Turn the rod (48) one turn to make it shorter.
_ 2 Remove and discard the cotter pin (602) and remove the nut
_ (601).
3 Pull out the bush (603) by 4 mm (0.1574 in.) to disengage it
_ from the stop flat (605).
4 Turn the bush (603) by the required correction value:
_ -0.9, -0.6, +0.6, +1.5 or +1.2. Make sure that the bush (603) stays engaged with its slots in the eccentric yoke (604).
NOTE : The slotted drive between the bush (603) and the
____ eccentric yoke (604) has a foolproofing device (one position only).
5 Push back the bush (603) until the correction value aligns
_ with the mark of the stop flat (605).
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-21Page 465 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Locking Hook Adjustment
Figure 416A/TASK 52-11-21-991-032-A12 (SHEET 1)
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-21Page 466 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Locking Hook Adjustment
Figure 416A/TASK 52-11-21-991-032-A22 (SHEET 2)
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-21Page 467 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
6_ Install and tighten the nut (601).
7_ Turn the barrel of the rod (48) until the locking hook (52)
touches the roller (58).
8_ Install the new cotter pin (602).
9_ Tighten the nuts (46) and the clamp (53).
10__ Make sure that the lockwashers (47) are correctly positioned.
11__ Safety the nuts (46) and the lockwashers (47) with
MISCELLANEOUS (Material No. 19-010).
(e) Open the door and remove the shims from the upper fittings (on the frame).
**ON A/C ALL
Subtask 52-11-21-420-056
F. Installation of the Locking Shaft (Ref. Fig. 408/TASK 52-11-21-991-015)
(1)
Make sure that the door is in the closed position.
(2)
Installation of the bearing assembly (110).
(a)
Apply SEALANTS (Material No. 09-018) on the surface of the bearing assembly (110), in contact with the door structure.
(b)
Install the bearing assembly (110), the bolts (111) and the nuts
(109) and tighten them.
(c)
Remove the unwanted sealant with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).
(3)
Install the bush (119) and the washer (118) on the upper locking shaft (117).
(4)
Apply COMMON GREASE (Material No. 04-004) on the surface of the shaft upper locking (117).
NOTE : When you install the lever assemblies (122), (127) and (129)
____ and the bellcrank assemblies (125) and (123) on the upper locking shaft (117), make sure that the grooves are aligned.
1EFF : ALL 1 52-11-21Page 468 1 1 May 01/03R 1 1 1CES 1
(5)
Put the upper locking shaft (117) in position.
(6)
Install the washer (120) and the bush (121).
(7)
Install the bellcrank assy (123) and the lever assembly (122).
(8)
Install the spacer (124).
(9)
Install the bellcrank assembly (125).
(10)
Install the lever assemblies (127) and (129) and the bushes (130) and (128).
(11)
Install the washer (108) and the nut (107). NOTE : If you install a new upper locking shaft (117), drill a hole
____ of 3.7 mm (0.1456 in.) for the cotter pin installation.
(12)
TORQUE the nut (107) to between 2.2 and 2.6 m.daN (16.22 and 19.17 lbf.ft).
(13)
Install a new cotter pin (106).
(14)
Install the lever assy (104), the taper pin (105), the washer (103) and the nut (102) and tighten.
(15)
Make sure that the grooves on the lever assy (104) are aligned with the grooves on the upper locking shaft (117).
(16)
Install a new cotter pin (101).
(17)
Connect the rod (67).
(a)
Put the rod (67) in position in its fitting.
(b)
Install the bushes (61) and (65) with SPECIAL MATERIALS (Material No. 05-002), the washer (66) and the bolt (90).
(c)
Install the washer (64) and the nut (62).
(d)
TORQUE the nut (62) to between 0.3 and 0.35 m.daN (26.54 and
30.97 lbf.in).
NOTE : If you install a new bolt (90), drill a hole of 1.9 mm
____ (0.0748 in.) for the cotter pin installation.
1EFF : ALL 1 52-11-21Page 469 1 1 May 01/03R 1 1 1CES 1
(18) Connect the rod (87).
(a)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门2(3)
