1EFF : ALL 1 52-13-22Page 407 1 1 Nov 01/99R 1 1 1CES 1
Escape Slide Gearbox Figure 402/TASK 52-13-22-991-002
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 408 May 01/98
Plate Assembly Figure 403/TASK 52-13-22-991-012
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 409 May 01/98
(2)
Remove the cotter pin (43) and discard it.
(3)
Remove the nut (44), the washers (42), the bolt (40), the washers
(41) and disengage the telescopic rod (45).
(4)
Remove the cotter pin (49) and discard it.
(5)
Remove the nut (50), the washer (48), the bolt (46), the washer (47) and remove the telescopic rod (45).
(6)
Remove the bolts (53), the washers (52), the bolt (55), the washer
(54) and remove the escape slide gearbox assembly (51). Subtask 52-13-22-020-053
C. Removal of the Percussion System
(Ref. Fig. 404/TASK 52-13-22-991-003)
(1)
Remove the cotter pins (166) and discard them.
(2)
Remove the nuts (167) and the washers (165).
(3)
Remove the bolts (186), the washers (185) and disconnect the rods (160), (184) and the flexible control (168).
(4)
Remove the cotter pin (173) and discard it.
(5)
Remove the nut (174), the washers (175), the bolt (178), the washer
(177) and remove the rod (184).
(6)
Remove the cotter pin (169) and discard it.
(7)
Remove the nut (170), the washer (171), the bolt (181), the washers (179), (180) and remove the bellcrank assembly (176) and the spacer (172).
Subtask 52-13-22-020-054
D. Removal of the Flexible Control Assembly
(Ref. Fig. 405/TASK 52-13-22-991-004)
(1)
Measure the dimension of the old flexible control
(Ref. Fig. 406/TASK 52-13-22-991-013)
(a) Measure and note the dimensions X1, X2, X3, X4.
(2)
Remove the cotter pin (85) and discard it.
1EFF : ALL 1 52-13-22Page 410 1 1 Nov 01/99R 1 1 1CES 1
Percussion System Figure 404/TASK 52-13-22-991-003
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 411 Nov 01/99
Flexible Control Figure 405/TASK 52-13-22-991-004- 12 (SHEET 1)
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 412 May 01/98
Flexible Control Figure 405/TASK 52-13-22-991-004- 22 (SHEET 2)
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 413 May 01/98
Flexible Control - Record of Dimensions Figure 406/TASK 52-13-22-991-013
1EFF : 1 1R 1CES ALL 1 11 1 52-13-22 Page 414 May 01/98
(3)
Remove the nut (84), the washer (83), the bolt (80) and the washer (81).
(4)
Remove the cotter pin (95) and discard it.
(5)
Remove the nut (94), the washer (96), the bolt (92) and the washer (93).
(6)
Remove the nuts (86) and the bolts (88).
(7)
Removal of the flexible control assembly (90).
(a)
Release the lockwasher (116).
(b)
Loosen the nut (115).
(c)
Remove the eye end assembly (117).
(d)
Remove the seal nut (114).
(e)
Loosen and remove the nut (113) and the washer (112).
(f)
Release the lockwasher (101).
(g)
Loosen the nut (102).
(h)
Remove the eye end assembly (100).
(i)
Remove the lockwasher (101) and the nut (102).
(j)
Remove the seal nut (103).
(k)
Loosen and remove the nut (105).
(l)
Remove the washer (106), the fitting (87) and the washer (104).
(m)
Disengage the flexible control (90) from the fittting (118).
(n)
Remove the flexible control (90) through the hole at the bottom of the door.
(8)
Disassembly of the flexible control (90).
(a)
Remove the washer (110).
(b)
Loosen and remove the nut (109).
1EFF : ALL 1 52-13-22Page 415 1 1 Nov 01/99R 1 1 1CES 1
(c) Loosen and remove the nut (107).
(d) Remove the flexible control (108). Subtask 52-13-22-020-055
E. Removal of the Girt Bar Control Shaft
(Ref. Fig. 407/TASK 52-13-22-991-006)
(1) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM DOORS 舱门2(142)
