R R 222TW, 222SW, 222UW, 222VW, 222RW, 232AW, 232CW (Ref. TASK 25-23-45-000-002).
R R R R R (b) For the AFT passenger/crew doors: - For the left door 832: 261TW, 261UW, 261VW, 261WW (Ref. TASK 25-23-45-000-003). - For the right door 842: 262TW, 262UW, 262VW, 262WW (Ref. TASK 25-23-45-000-004).
Subtask 52-10-00-410-064
C. Closing of the Door
(1) Close the door from the inner side (Ref. TASK 52-10-00-410-001).
4. Procedure_________
Subtask 52-10-00-220-057
A. Check of the Adjustment of the Door Stops (Ref. Fig. 504/TASK 52-10-00-991-015)
(1) Make sure that the clearance A between the stop screw (2) and the door frame fitting (1) is 0 +0 +0.5 mm (0.0000 +0.0000 +0.0196 in.).
(2) Make sure that a minimum of three stop screws touches the door frame with: - two stop screws on one side of the frame and, - one stop screw on the opposite side of the frame. If necessary, adjust the door stops (Ref. TASK 52-11-00-820-001) or (Ref. TASK 52-13-00-820-001).
5. Close-up________
Subtask 52-10-00-010-101
A. Opening of the Door
(1) Open the door from the inner side (Ref. TASK 52-10-00-010-001).
Door Stop Adjustment Figure 504/TASK 52-10-00-991-015
1EFF : 1 1R 1CES ALL 1 11 1 52-10-00 Page 535 May 01/04
R Subtask 52-10-00-410-110-A
R B. Installation of the Components
R (1) Install the door-frame lining panels:
R R R R R R R (a) For the FWD passenger/crew doors: - For the left door 831: 221AW, 221BW, 221CW, 221EW, 221FW, 221VW, 221SW 221RW 231AW, 231CW (Ref. TASK 25-23-45-400-006) - For the right door 841: 222TW, 222SW, 222UW, 222VW 222RW 232AW, 232CW (Ref. TASK 25-23-45-400-007).
R R R R R (b) For the AFT passenger/crew doors: - For the left door 832: 261TW, 261UW, 261VW, 261WW (Ref. TASK 25-23-45-400-008). - For the right door 842: 262TW, 262UW, 262VW, 262WW (Ref. TASK 25-23-45-400-005).
Subtask 52-10-00-410-065
C. Close Access
(1) Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).
(2) Make sure that the work area is clean and clear of tool(s) and other items.
(3) Close the applicable passenger/crew door 831 (841) or 832 (842) (Ref. TASK 52-10-00-410-001).
(4) Remove the access platform(s).
1EFF : ALL 1 52-10-00Page 536 1 1 Feb 01/05 1 1 1CES 1
TASK 52-10-00-720-005
Functional Test of the Release Mechanism of the Emergency Escape Slide
1.
Reason for the Job
__________________
Refer to the MPD TASK: 521000-06
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific dynamometer 20 daN (44.9617 lbf)
No specific access platform 3.5 m (11 ft. 6 in.)
98D52103500000 1 SAFETY PIN - SLIDE ARMING
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door
**ON A/C 001-002,
52-10-00-991-016 Fig. 505
**ON A/C 003-049, 051-099, 101-105, 151-158, 201-210,
52-10-00-991-016-B Fig. 505A R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
52-10-00-991-016-C Fig. 505B
1EFF : ALL 1 52-10-00Page 537 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________ Subtask 52-10-00-010-063
A. Get Access WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
THAN 65 KNOTS.
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(95)
