(2)
Make sure that the weight fitting (1) is in position on the base plate (2). (Ref. Fig. 206/TASK 52-10-00-991-050)
(3)
If the weight fitting (1) is not in position on the base plate (2), install the weight fitting on the base plate as follows: (Ref. Fig. 206/TASK 52-10-00-991-050)
(a)
Tighten the shoulder screws (5) and the nuts (6) on the base plate (2).
(b)
Install the weight fitting (1) on the base plate (2).
(c)
Install the nut (7) and tighten it.
4. Procedure
_________ Subtask 52-10-00-480-051
A. Installation of the Ballast Weight
(1) Install the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) as follows:
(a) Install the base plate with the weight fitting on the door as follows: (Ref. Fig. 206/TASK 52-10-00-991-050)
R 1EFF : 003-049, 051-099, 101-149, 151-199, 1 52-10-00Page 229 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 1 Lift the base plate (2) with the weight fitting (1) on to the
_
supports (12).
NOTE : Two persons are necessary for this step, one on each
____ side of the base plate (2). The base plate (2) with the weight fitting (1) weighs 23 kg (50.705 lb).
2 Install the pins (4) and tighten them.
_ a For the aft doors: on the upper holes in the upper corners
_
of the base plate.
b For the forward doors: on the lower holes in the upper
_
corners of the base plate.
(b) Install the weight assy with the weights N1 as follows: (Ref. Fig. 205A/TASK 52-10-00-991-049-A)
1 Install the pin (11) in the rear center hole of the weight
_
fitting (1).
2 Install the nut (8) and tighten it.
_
3 Install the weights N1 (10) and the pin (9) on the pin (11).
_
(c) Install the three weight assemblies with the weights N2 as follows: (Ref. Fig. 205A/TASK 52-10-00-991-049-A)
1 Install the weights N2 (5) in position on the center of the
_ slots against the front edge of the weight fitting (1).
2 Install the pins (6) through the weights N2 (5) and the weight
_
fitting (1).
NOTE : Make sure that the studs (7) are fully engaged in the
____
slots of the weights N2 (5).
3 Install the nuts (3) and tighten them.
_
R 1EFF : 003-049, 051-099, 101-149, 151-199, 1 52-10-00Page 230 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 PASSENGER/CREW - SERVICING
__________________________
TASK 52-10-00-614-001
Discharging/Charging of the Damper and Emergency Operation Cylinder of the Passenger/Crew Doors
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific nitrogen filling system equipped with a pressure
gauge
No specific union, dia. 0.30 inch., 32 threads per inch.
No specific access platform 3 m (9 ft. 10 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door
52-10-00-410-001 Closing of the Passenger/Crew Door
52-10-00-790-001 Leak Test of the Damper and Emergency Operation
Cylinder of the Passenger/Crew Doors 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door 52-10-00-991-029 Fig. 301
1EFF : ALL 1 52-10-00Page 301 1 1 May 01/05 1 1 1CES 1
3. Job Set-up
__________
Subtask 52-10-00-010-075
A. Get Access
WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
THAN 65 KNOTS.
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
- 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(75)
