(c)
Tighten the screws (40).
(4)
When the door is in the down position, make sure that:
(a)
The rollers (31) of the guide fittings (32), (36) turn freely.
(b)
The clearance C4 is 0.2 mm (0.0078 in.) to 1.5 mm (0.0590 in.).
(c)
The clearance C3 is 0.2 mm (0.0078 in.) minimum.
(d)
The clearance C5 is 3 mm (0.1181 in.) to 6 mm (0.2362 in.). NOTE : A clearance C5 of 3 mm (0.1181 in.) to 8 mm (0.3149 in.)
____
is permitted.
(e)
If the clearances C3 and C4 are not in the tolerances, adjust the upper and lower guide fittings (32), (36).
(5)
When the door is closed, make sure that the clearance C6 is 0.2 mm (0.0078 in.), between the rollers (31) and the stop screws (35).
Subtask 52-11-00-820-054
D. Check in the Z Axis of the Door and Locking Hook Adjustment
(Ref. Fig. 502/TASK 52-11-00-991-005, 508/TASK 52-11-00-991-012)
(1)
Close the door.
(2)
Make sure that:
(a)
The clearance C6 between the rollers (31) and the bolts (35) is
0.2 mm (0.0078 in.).
(b)
The locking hook (41) is in contact with the roller (40).
R 1EFF : 001-049, 051-056, 1 52-11-00Page 528 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper Hook of the FWD Passenger/Crew Door
Figure 508/TASK 52-11-00-991-012
R 1EFF : 001-049, 051-056, 1 52-11-00Page 529 1 1 May 01/05 1 1 1CES 1
(3)
If the clearance C6 is not in the tolerances do the adjustment below:
(a)
Open the door.
(b)
Remove the nuts (34), the adjustable washers (33), and the bolts (35).
(c)
Install the bolts (35) and the nuts (34).
(d)
Put the two shims (thickness 0.2 mm (0.0078 in.)) in position in the upper guide fittings (32).
(e)
Close the door and measure the dimension between the rollers (31) and the bolts (35).
(f)
Open the door, remove the nuts (34), the bolts (35) and the two shims.
(g)
Adjust the thickness of the adjustable washers (33).
(h)
Install the adjustable washers (33), the bolts (35) and the nuts
(34) and tighten them.
(4)
If there is no contact at the locking hook (41), do the adjustment below:
(a)
Put the two shims (thickness 0.2 mm (0.0078 in.)) in position in the upper guide fittings (32).
(b)
Close the door.
(c)
Remove and discard the lockwire from the nuts (42).
(d)
Loosen the nuts (42) and release the lockwashers (43).
(e)
Loosen the clamp (45).
(f)
Turn the barrel of the rod (44) until you get the contact between the locking hook (41) and the roller (40).
(g)
Tighten the nuts (42) and the clamp (45).
(h)
Make sure that the lockwashers (43) are correctly positioned.
(i)
Safety the nuts (42) and the lockwashers (43) with MISCELLANEOUS (Material No. 19-010).
R 1EFF : 001-049, 051-056, 1 52-11-00Page 530 1 1 May 01/05 1 1 1CES 1 (j) Open the door and remove the two shims.
(5) Make sure that, when the door is closed, the roller (40) turns freely.
R **ON A/C 057-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-00-820-053-A
C. Check and Adjustment of Clearances between the Rollers and the Guide Fittings (Ref. Fig. 502A/TASK 52-11-00-991-005-A)
(1)
Operate the door several times.
(2)
With the door in the up position, make sure that:
(a) The guide rollers (31) move off the guide fittings (32), (36) with the clearances below:
1 C1 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
_
2 C2 is 0.2 mm (0.0078 in.) to 2.2 mm (0.0866 in.).
_
(3)
If the clearances C1 and C2 are not in the tolerances, adjust the guide fittings (32), (36) as specified below:
(a)
Open the door and identify the position of the serrations of the plates (37), (38) on the upper and lower guide fittings (32), (36).
(b)
Loosen the screws (40) and move the guide fittings (32), (36) to get the correct clearances C1 and C2.
(c)
Make sure that the eccentric washers (39):
-fully seal the holes of the guide fittings (32) and (36),
-
are not above the rounded areas or spot-facing edges,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(116)
