R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
52-10-00-991-030-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 52-10-00-010-083
A. Get Access
(1)
Put the access platform in position in the zone 831 (841) or 832 (842).
(2)
Open the applicable passenger crew/door 831, 841 or 832, 842 (Ref. TASK 52-10-00-010-001).
(3)
Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).
1EFF : ALL 1 52-10-00Page 402 1 1 Aug 01/05 1 1 1CES 1 Subtask 52-10-00-865-073
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
**ON A/C 001-002,
Subtask 52-10-00-010-084
C. Removal of the Escape Slide
(1)
Remove the door linings panels:
(a)
For the FWD passenger crew/doors:
(Ref. TASK 25-23-46-000-001)
-for the left door 831AZ
-For the right door 841AZ
(b)
For the Aft passenger crew/doors:
(Ref. TASK 25-23-46-000-002)
-
for the left door 832AZ
-
for the right door 842AZ
(2)
Remove the escape slide (Ref. TASK 25-62-44-000-002).
R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-10-00-010-084-A
C. Removal of the Escape Slide Raft
(1) Remove the door lining panels:
(a) For the FWD passenger crew/doors:
(Ref. TASK 25-23-46-000-001)
-
For the left door 831AZ
-
For the right door 841AZ
1EFF : ALL 1 52-10-00Page 403 1 1 Aug 01/05 1 1 1CES 1
(b) For the Aft passenger crew/doors:
(Ref. TASK 25-23-46-000-002)
-
for the left door 832AZ
-
for the right door 842AZ
(2) Remove the escape slide/raft (Ref. TASK 25-62-44-000-002).
**ON A/C ALL
4. Procedure
_________
Subtask 52-10-00-820-050
A. Load Ajustment of the Inner Control Handle
**ON A/C 001-002,
(Ref. Fig. 401/TASK 52-10-00-991-030) R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 52-10-00-991-030-A)
**ON A/C ALL
(1)
Remove the lockwire from the screw (2).
(2)
Measure the loads on the inner control handle with a dynamometer, 20 da.N when the door is in the up and down positions.
(3)
Make sure that the load necessary to open and close the door with the inner control handle is less than or equal to 16 daN (35.9694 lbf).
(4)
Adjust the load. To do this, turn the screw (2) to apply a load on the torsion bar (1).
(5)
Safety the screw (2) with MISCELLANEOUS (Material No. 19-010)
1EFF : ALL 1 52-10-00Page 404 1 1 Aug 01/05 1 1 1CES 1
Load Adjustment of the Inner Control Handle
Figure 401/TASK 52-10-00-991-030
1EFF : 001-002, 1 52-10-00Page 405 1 1 Feb 01/04 1 1 1CES 1
Load Adjustment of the Inner Control Handle Figure 401A/TASK 52-10-00-991-030-A
R 1EFF : 003-049, 051-099, 101-149, 151-199, 1 52-10-00Page 406 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 52-10-00-865-074
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
Subtask 52-10-00-410-092
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(82)
