• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-26 23:38来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 Install the stop (303) with the adjustable shim (302) and the nut (301).

 (d)
 TORQUE the nut (301) to 0.68 m.daN (60.17 lbf.in).


 (e) Do step (3) again. **ON A/C 221-223, 225-230, 301-302,
 Subtask 52-11-00-820-061-A
 L. Check of the Outer Control Handle Locking
 (Ref. Fig. 513A/TASK 52-11-00-991-015-A)

 (1)
 Open the door from the outer side and close the door from the inner side.

 (2)
 Make sure that the handle flap (304) comes back to its initial position when you close the door from the outer side.

 (3)
 Apply a manual pressure on the handle flap (304) until it touches the stop (303). Release the handle flap and make sure that the handle flap (304) goes back to its initial position.


 NOTE : Do this procedure five times.
____
 1EFF : ALL 1 52-11-00Page 550 1 1 May 01/05R 1 1 1CES 1


 Adjustment of the Outer Control Handle of the FWD Passenger/Crew Door Figure 513A/TASK 52-11-00-991-015-A
R 1EFF : 221-223, 225-230, 301-302, 1 52-11-00Page 551 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL


 Subtask 52-11-00-820-062
 M. Check of the Emergency Control Handle Disarming
 (1)
 Close the door.

 (2)
 Put the emergency control handle in the ARMED position.

 (3)
 Open the door with the outer control handle.

 (4)
 Make sure that the emergency control handle moves to the DISARMED position.


 Subtask 52-11-00-820-063
 N. Check of the Door Locking in the UP Position
 (Ref. Fig. 514/TASK 52-11-00-991-014)

 (1)
 Make sure that during the opening of the door, the inner control handle (405) locks before release of the rollers from the guide fittings

 (2)
 Make sure that when you close the door with the inner control handle

 (405) you feel no hard points caused by the non-retraction of the hooks (404).

 (3)
 If necessary, do the adjustment below:

 (a)
 Remove the lockwire from the nuts (401), (403) and discard it.

 (b)
 Decrease the length of the rod (403) shorter so that when you close the door, there is no hard point caused by the non-retraction of the hook with the door in the up position.

 (c)
 Tighten the nuts (401), (403) and safety them with MISCELLANEOUS (Material No. 19-010).

 (d)
 Put the door in the up position and make sure that you can correctly install the RIGGING PIN (98DNSA20206120).

 

 (4)
 If you continue to feel the hard point, apply COMMON GREASE (Material No. 04-004) to the contact surface of the hook (404) and the handle (405).


 1EFF : ALL 1 52-11-00Page 552 1 1 May 01/05R 1 1 1CES 1


 Adjustment of the Inner Contol Handle of the FWD Passenger/Crew Door Figure 514/TASK 52-11-00-991-014
 1EFF : ALL 1 52-11-00Page 553 1 1 May 01/05R 1 1 1CES 1


 Subtask 52-11-00-820-065
 P. Check of Preload of the Cover Plate
 (1) Do a check of the preload of the cover plate (Ref. TASK 52-10-00-220-007).
 NOTE : Do this check only after the replacement of the door by a new
____
 door.

 NOTE : After adjustment of the door, you can possibly see a permitted
____
 bend line on the cover plate.

 Subtask 52-11-00-820-066
 Q. Check and Adjustment of the Proximity Switch.
 (1) Do an adjustment of the proximity switch of the door locking mechanism 11WV1 or 11WV2 (Ref. TASK 52-71-00-820-001).
 5. Close-up
________
 **ON A/C 001-002,

 Subtask 52-11-00-020-053
 A. Removal of the Ballast Weight
 (1) Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001) or the escape slide (Ref. TASK 25-62-44-400-001) if previously kept in position (as an alternative to the ballast weight).
R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 52-11-00-020-053-A
 A. Removal of the Ballast Weight
 (1) Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001) or the escape slide/raft (Ref. TASK 25-62-44-400-001) if previously kept in position (as an alternative to the ballast weight).
 1EFF : ALL 1 52-11-00Page 554 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL


 Subtask 52-11-00-865-053
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM DOORS 舱门1(121)