R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire dia. 0.8mm (0.032 in.) Material No. 02-001 USA MIL-H-5606 OIL, HYDRAULICPETROLEUM FLUID (Ref. 20-31-00) Material No. 11-008A SOLVENT,WHITE SPIRIT WITH ALCOHOL (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 52-10-00Page 306 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 52-10-00Page 307 1 1 May 01/04 1 1 1CES 1
R C. Expendable Parts
R R R -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R R R 5 6 7 12 packings seal diaphragm shear pin 52-11-14 01B-020 52-11-14 01B-030 52-11-14 01B-040A 52-11-14 01B-110
R D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
25-23-46-000-001 25-23-46-000-002 25-23-46-400-001 25-23-46-400-002 52-10-00-010-001 52-10-00-614-001 52-10-00-860-001 52-10-00-860-002 52-10-00-991-036 Removal of the Door Linings at the FWD Passenger/Crew DoorsRemoval of the Door Linings at the AFT Passenger/Crew DoorsInstallation of the Door Linings at the FWD Passenger/Crew DoorsInstallation of the Door Linings at the AFT Passenger/Crew DoorsOpening of the Passenger/Crew DoorDischarging/Charging of the Damper and Emergency Operation Cylinder of the Passenger/Crew DoorsSpecial Precautions before Work on the Passenger/Crew DoorSpecial Precautions after Work on the Passenger/Crew DoorFig. 302
3. Job Set-up
__________
Subtask 52-10-00-941-069
A. Get Access
WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
THAN 65 KNOTS.
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
R (1) Put an access platform in front of the passenger/crew door 831 (841) R or 832 (842).
(2)
Open the passenger/crew door 831 (841) or 832 (842) (Ref. TASK 52-10-00-010-001).
(3)
Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).
Subtask 52-10-00-865-071
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
Subtask 52-10-00-020-052
C. Removal of the Components
(1) Remove the lining panels 831FZ (841FZ) and 831GZ (841GZ) (Ref. TASK 25-23-46-000-001) or 832FZ (842FZ) and 832GZ (842GZ) (Ref. TASK 25-23-46-000-002).
1EFF : ALL 1 52-10-00Page 308 1 1 May 01/04 1 1 1CES 1 1EFF : ALL 1 52-10-00Page 309 1 1 May 01/04 1 1 1CES 1
(2) Bleed the pressurized bottle with the valve (10) until the pressure gage shows "0".
4. Procedure_________
Subtask 52-10-00-020-053
A. Removal
WARNING : MAKE SURE THAT YOU INSTALL THE CORRECT (ALUMINUM) SHEAR PIN ON_______ THE DOOR-DAMPER PERCUSSION DEVICE. INSTALLATION OF AN INCORRECT SHEAR PIN WILL PREVENT OPERATION OF THE ACTUATOR IN THE EMERGENCY MODE.
(Ref. Fig. 302/TASK 52-10-00-991-036)
(1) Cut and remove the lockwire from the knurled screw (1).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(77)
