(Ref. Fig. 407/TASK 52-11-11-991-006)
(1)
Slowly put the door in position in the door frame (the upper and lower guide arms are not installed).
(2)
Make sure that the guide rollers (101) of the door enter into the guide fittings (102) and (106).
(3)
Make sure that the contact of the door and the seal is correct at the front and rear vertical frame sections.
(4)
If the contact is not correct.
(a) On the Z axis:
(Ref. Fig. 408/TASK 52-11-11-991-005)
1 Remove the lockwire from the nuts (201) and (203), and discard
_
it.
2 Loosen the nuts (201) and (203).
_ 3 Adjust the length of the rod (202) until you get the correct
_
configuration.
4 Tighten the nuts (201) and (203), and safety the rod (202)
_ with MISCELLANEOUS (Material No. 19-010).
1EFF : ALL 1 52-11-11Page 424 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Door Stop Fittings Figure 407/TASK 52-11-11-991-006
1EFF : 1 1R 1CES ALL 1 11 1 52-11-11 Page 425 Feb 01/04
Clearances - Adjustments on the Z Axis Figure 408/TASK 52-11-11-991-005
R 1EFF : 1 1 1CES ALL 1 111 52-11-11 Page 426 Feb 01/04
(b) On the X axis: (Ref. Fig. 403/TASK 52-11-11-991-004, 408/TASK 52-11-11-991-005)
1 Disconnect the upper and lower connection links (61) from each
_
side of the yoke (65).
2 Remove the nuts (70), the washers (71), (62) and the bolts
_
(63) to disconnect the upper and lower connection links (61). 3 Adjust the door in the X axis with the washers (64) of a
_
different thickness.
4 Make sure that the clearance B is less than or equal to 0.1 mm
_
(0.0039 in.).
NOTE : The thickness of the two washers (64) at level of the
____ lower and upper connection links (61) is equal to the nominal thickness. Clearance B must be in the tolerances
5 Connect the upper and lower connections links (61).
_
6 Install the washers (62) and the bolts (63).
_
7 Install the washers (71) and the nuts (70).
_
(5) Make sure that when you start to open the door the clearance H1 between the door stops (301) and the door frame stops (302) is 5 mm (0.1968 in.) minimum.
R **ON A/C 001-049, 051-056,
Subtask 52-11-11-820-067
C. Adjustment of the Door in its Frame during the Door Closing Operation (Ref. Fig. 406/TASK 52-11-11-991-011, 407/TASK 52-11-11-991-006, 409/TASK 52-11-11-991-020, 410/TASK 52-11-11-991-012)
(1)
Slowly close the door and make sure that there is no hard contact between the door stops (301) and the frame stops (302).
(2)
The clearance H2 must be 0.2 mm (0.0078 in.) minimum for an overlap H3 of 3 mm (0.1181 in.) to 4 mm (0.1574 in.). The guide rollers (101) are in contact with the guide fittings (102) and (106).
1EFF : ALL 1 52-11-11Page 427 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409/TASK 52-11-11-991-020
R 1EFF : 001-049, 051-056, 1 52-11-11Page 428 1 1 May 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
52-11-11Page 429
1 1 Feb 01/04 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409A/TASK 52-11-11-991-020-A12 (SHEET 1)
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-11Page 430 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409A/TASK 52-11-11-991-020-A22 (SHEET 2)
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-11Page 431 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Girt Bar Fittings - Clearances and Adjustments Figure 410/TASK 52-11-11-991-012
1EFF : 1 1R 1CES ALL 1 11 1 52-11-11 Page 432 Feb 01/04
(3)
If the clearance H2 is not in the tolerances, adjust the upper and lower guide fittings (102) and (106) as follows:
(a)
Open the door and identify the position of the serration plates
(107) and (108), and the upper and lower guide fittings (102), (106).
(b)
Loosen the screws (110) and move the guide fittings (102), (106) to get the clearance H2 and temporarily tighten the screws (110).
(4)
Release the upper hook as follows:
(Ref. Fig. 409/TASK 52-11-11-991-020)
(a)
Remove and discard the lockwire from the nuts (115).
(b)
Loosen the nuts (115) and release the lockwashers (114).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(135)
