1EFF : ALL 1 52-11-18Page 408 1 1 Nov 01/98 1 1 1CES 1
R R Door Seal - Clearances Figure 402/TASK 52-11-18-991-006
1EFF : 1 1 1CES ALL 1 111 52-11-18 Page 409 Nov 01/98
(3)
Close the passenger/crew door 831, 841 (Ref. TASK 52-10-00-410-001).
(4)
Remove the access platform(s).
1EFF : ALL 1 52-11-18Page 410 1 1 Nov 01/98 1 1 1CES 1 SEAL - DOOR - REPAIRS
_____________________
TASK 52-11-18-300-001
Repair of the Seal of the FWD Passenger/Crew Door
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific clamp
No specific fine emery paper
No specific lint-free cloth
No specific spatula
No specific very fine emery paper
No specific Wooden Bonding Block
No specific access platform 4.40 m (14 ft. 5 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-023 USA MIL-I-631 POLYTEREPTHALATE (Ref. 20-31-00) Material No. 05-024 FABRIC (Ref. 20-31-00) R Material No. 08-004 USA MIL-A-25457 ADHESIVE SEALANT (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
1EFF : ALL 1 52-11-18Page 801 1 1 Nov 01/99 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew
Door 52-11-18-000-001 Removal of the Door Seal 52-11-18-400-001 Installation of the Door Seal 52-11-18-991-002 Fig. 801 52-11-18-991-003 Fig. 802 52-11-18-991-004 Fig. 803 52-11-18-991-005 Fig. 804
3. Job Set-up
__________
Subtask 52-11-18-941-051
A. Get Access
WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
THAN 65 KNOTS.
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
(1)
Put the access platform in position in the zone 831 or 841.
(2)
Open the door 831 or 841 (Ref. TASK 52-10-00-010-001).
(3)
Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).
1EFF : ALL 1 52-11-18Page 802 1 1 Feb 01/98 1 1 1CES 1 Subtask 52-11-18-020-051
B. Seal Removal.
(1) Remove the door seal (Ref. TASK 52-11-18-000-001).
4. Procedure
_________
(Ref. Fig. 801/TASK 52-11-18-991-002, 802/TASK 52-11-18-991-003, 803/TASK
52-11-18-991-004, 804/TASK 52-11-18-991-005) Subtask 52-11-18-340-050
A. Repair the Signs of Chafing on the Seal.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(163)
