(c)
Loosen the clamp (113).
(d)
Turn the barrel of the rod (112) to retract it.
(5)
Slowly close the door and make sure that there is no hard contact between the telescopic fork ends (402) and the girt bar fittings
(401)
(Ref. Fig. 410/TASK 52-11-11-991-012)
R **ON A/C 057-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-11-820-067-A
C. Adjustment of the Door in its Frame during the Door Closing Operation (Ref. Fig. 406A/TASK 52-11-11-991-011-A, 407/TASK 52-11-11-991-006, 409A/TASK 52-11-11-991-020-A, 410/TASK 52-11-11-991-012)
(1)
Slowly close the door and make sure that there is no hard contact between the door stops (301) and the frame stops (302).
(2)
The clearance H2 must be 0.2 mm (0.0078 in.) minimum for an overlap H3 of 3 mm (0.1181 in.) to 4 mm (0.1574 in.). The guide rollers (101) touch the guide fittings (102) and (106).
1EFF : ALL 1 52-11-11Page 433 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 52-11-11Page 434 1 1 Feb 01/04 1 1 1CES 1
R (3) If the clearance H2 is not in the tolerances, adjust the upper and
R lower guide fittings (102) and (106) as follows:
R (a) Open the door and identify the position of the serration plates
R (107) and (108), and the upper and lower guide fittings (102),
R (106).
R (b) Loosen the screws (110) and move the guide fittings (102), (106)
R to get the clearance H2.
R (c) Make sure that the eccentric washers (109):
R - fully seal the holes of the guide fittings (102) and (106),
R - are not above the rounded areas or spot-facing edges,
R - are not out of the outer contour of the fitting.
R (d) Temporarily tighten the screws (110).
R (4) Release the upper hook as follows:
R (Ref. Fig. 409A/TASK 52-11-11-991-020-A)
R (a) Remove and discard the lockwire from the nuts (115).
R (b) Loosen the nuts (115) and release the lockwashers (114).
R (c) Loosen the clamp (113).
R (d) Turn the barrel of the rod (112) to retract it.
R (5) Slowly close the door and make sure that there is no hard contact
R between the telescopic fork ends (402) and the girt bar fittings
R (401)
R (Ref. Fig. 410/TASK 52-11-11-991-012)
R **ON A/C ALL
Subtask 52-11-11-820-050
D. Adjustment of the Door in the Down Position
(Ref. Fig. 403/TASK 52-11-11-991-004, 408/TASK 52-11-11-991-005, 411/TASK
52-11-11-991-008)
(1) Install two positioning templates on the X axis on the door frame
(Ref. Fig. 411/TASK 52-11-11-991-008)
(a) Install one template between the longerons L5 and L6.
INTENTIONALLY BLANK
R 1 1
52-11-11Page 435
1 1 Feb 01/04 1 1 1CES 1
Adjustment of the Door in the Door Frame Figure 411/TASK 52-11-11-991-008- 13 (SHEET 1)
1EFF : 1 1R 1CES ALL 1 11 1 52-11-11 Page 436 Feb 01/04
Adjustment of the Door in the Door Frame Figure 411/TASK 52-11-11-991-008- 23 (SHEET 2)
1EFF : 1 1R 1CES ALL 1 11 1 52-11-11 Page 437 Feb 01/04
Adjustment of the Door in the Door Frame Figure 411/TASK 52-11-11-991-008- 33 (SHEET 3)
1EFF : 1 1R 1CES ALL 1 11 1 52-11-11 Page 438 Feb 01/04
(b) Install the other template between the longerons L2 and L3.
(2) If the templates do not touch the door frame or the door contour in the X axis: (Ref. Fig. 403/TASK 52-11-11-991-004)
(a)
Disconnect the upper and lower connection links (61) from each side of the yoke (65).
(b)
Remove the nuts (70), the washers (71), (62) and the bolts (63) to disconnect the upper and lower connection links (61).
(c)
Adjust the door in the X axis with the washers (64) of a
different thickness.
(d)
Make sure that the clearance B is less than or equal to 0.1 mm (0.0039 in.).
NOTE : The thickness of the two washers (64) at level of the
____ lower and upper connection links (61) is equal to the nominal thickness. Clearance B must be in the tolerances.
(e)
Connect the upper and lower connection links (61).
(f)
Install the washers (62), the bolts (63).
(g)
Install the washers (71) and the nuts (70).
(3) Do a check of the peripheral clearance between the door and the door frame:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门1(136)
