3. Job Set-up
__________
Subtask 36-11-49-861-064
A. Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
Subtask 36-11-49-941-052
B. Safety Precautions
(1)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(2)
On the AIR COND panel 30VU:
-make sure that the ENG 1(2) BLEED pushbutton switch is released
(the OFF legend is on), R - make sure that the APU BLEED pushbutton switch is released (the ON R legend is off),
-put a warning notice to tell persons not to operate the pneumatic system.
(3)
On the ENG panel 115VU:
-put a warning notice to tell persons not to start the engine 1(2).
(4)
On the HP ground connector:
-Put a warning notice to tell persons not to pressurize the pneumatic system.
(5)
On the ENG section of the maintenance panel 50VU:
-make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
-put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 36-11-49-865-053
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22
Subtask 36-11-49-010-051
D. Get Access
(1)
Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2)
Put the access platform in position in zone 450 for engine 1 and in zone 460 for engine 2.
Subtask 36-11-49-040-057
E. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 36-11-49-010-094
F. Open the thrust reverser cowl doors (Ref. TASK 78-36-00-010-040):
FOR 1000EM1
451AL, 452AR
FOR 1000EM2
461AL, 462AR
4. Procedure
_________
(Ref. Fig. 402/TASK 36-11-49-991-301) Subtask 36-11-49-020-051
A. Removal of the Mid-Stage Tee Duct
(1)
Remove the coupling (10) and the E-seal (15) that connect the mid stage tee duct (20) to the bleed pressure regulator valve (5).
(2)
Remove the E-seal (15) and the coupling (10) that connect the mid stage tee duct (20) to the High Pressure (HP) bleed valve (40).
(3)
Remove the coupling (10) and the E-seal (15) that connect the mid stage tee duct (20) to the HP bleed check valve (45).
(4)
Disconnect the tube from the union (55) in the mid stage tee duct (20).
(5)
Remove the union (55) from the mid stage tee duct (20).
(6)
Remove the nuts (35), the washers (30), and the bolts (25), from the support links (50) that are connected to the brackets on the mid stage tee duct (20).
(7)
Move the support links (50) clear of the mid stage tee duct (20) and remove the duct from the engine.
(8)
Put blanking plugs on the ends of the mid stage tee duct (20).
(9)
Put blanking plugs on the bleed pressure regulator valve (5), the HP bleed valve (40), and the Intermediate Pressure (IP) bleed check valve (45).
Mid Stage Tee Duct
Figure 402/TASK 36-11-49-991-301
1EFF : ALL 1 36-11-49 Page 414
1 1 Feb 01/98
1 1
1CES 1
(10) Put protective covers on the HP sense tube and the boss on the mid stage tee duct (20).
TASK 36-11-49-400-043
Installation of the Mid Stage Tee Duct
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM PNEUMATIC 气源 1(121)
