• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-20 12:12来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 C.  Check that indicator instrument lighting is on.
 D.  Remove electrical power if no longer required (Ref 24-22-00).
 EFFECTIVITY
 LH 011-030,051-070,082-099

 AF 121-199; AZ 221-299; AND GN 601-699 AIRPLANES  CONFIG 1 WITHOUT PMS  10 Page 202
   Sep 25/94

34-15-00
 TOTAL AIR TEMPERATURE/ENGINE PRESSURE RATIO LIMIT SYSTEM -
__________________________________________________________ MAINTENANCE PRACTICES
_____________________
 1.  General
_______
 A.  This section covers the removal and installation of the TAT/EPRL computer, A/T-TAT/EPRL mode selector panel and TAT/EPRL indicator. Procedures for the computer, mode selector panel and indicator are obvious and only safety related steps are given.
 2.  Referenced Procedures
_____________________
 A.  20-11-13, Cam-Lock Lever Latch Fork Adjustment, Type V
 B.  24-22-00, Maintenance Practices (Apply Power)
 C.  33-11-09, Lighted Pushbutton Switches
 3.  Removal of TAT/EPRL Computer
____________________________
 A.  Before removing unit, open TAT/EPRL-COMP and TAT/EPRL IND circuit breakers on P7 panel.
 4.  Removal of A/T-TAT/EPRL Mode Selector Panel
___________________________________________
 A.  Before removing panel, open the following circuit breakers:
 (1)  
TAT/EPRL - COMP on P7 panel

 (2)  
SEC PROTECTION on pilots' control stand P8 for control stand panel lights dimmer T144

 (3)  
IND LTS-PILOTS and SW LTS on P12 panel


 B.  After removing panel, remove RTG I and RTG II switch caps from panel (Ref 33-11-09). Retain in airplane to install on new panel.
 5.  Removal of TAT/EPRL Indicator
_____________________________
 A.  Before removing indicator, open the following circuit breakers:
 (1)  
TAT/EPRL-COMP and TAT/EPRL-IND on P7 panel

 (2)  
SEC PROTECTION on pilots' control stand P8 for center instrument panel lights dimmer T137


 6.  Installation of TAT/EPRL Computer
_________________________________
 A.  Before installing unit, ensure that circuit breakers listed in par.
 3.A. are open.
 B.  Install computer (Ref 20-11-13).
 CAUTION: IMPROPER ADJUSTMENT OF CAM LOCK LATCH ON EQUIPMENT SHELF
_______ MAY CAUSE CIRCUIT MALFUNCTION OR EQUIPMENT DAMAGE.
 C.  Close TAT/EPRL-COMP, TAT/EPRL-IND, CADC 1 and CADC 1 - SYNC EXCIT circuit breakers on panel P7.
 D.  Press TEST LAMPS switch on computer; three failure lights should come on. Releast switch; lights should go out.
 E.  Remove electrical power if no longer required (Ref 24-22-00).
 7.  Installation of A/T-TAT/EPRL Mode Selector Panel
________________________________________________
 A.  Install RTG I and RTG II switch caps (Ref 33-11-09) on panel.
 B.  Before installing panel, ensure that circuit breakers listed in par. 4.A.(1), (2) and (3) are open.
 C.  Install control panel and close circuit breakers opened in par. 4.A.(1), (2) and (3).
 D.  Check that panel lights are on.
 E.  Remove electrical power if no longer required (Ref 24-22-00).
 8.  Installation of TAT/EPRL Indicator
__________________________________
 EFFECTIVITY

 AT ALL; MD ALL; VM ALL;  CONFIG 2 IB 406-499  14 Page 201  Apr 25/85

34-15-00
 A.  Before installing indicator, ensure that circuit breakers listed in par. 5.A.(1) and (2) are open.
 B.  Install indicator and close circuit breakers opened in 5.A.(1) and (2).
 C.  Check that indicator instrument lighting is on.
 D.  Remove electrical power if no longer required (Ref 24-22-00).
 EFFECTIVITY

 AT ALL; MD ALL; VM ALL;  CONFIG 2 IB 406-499  17 Page 202  Apr 25/85

34-15-00
 XA A/T-TAT/N1 (EPRL) MODE SELECT PANEL - SERVICING (RELAMPING)
___________________________________________________________
 XA 1. _______
General XA A. The A/T-TAT/N1 (EPRL) mode select panel is located on the aft control XA stand electronics panel. Lamps in RTG I and RTG II switch caps (Ref XA 33-11-09) and the N1 (EPR) derate display may be replaced while XA installed in the airplane. XA 2. _______________________________
Replace N1 (EPR) Derate Display XA A. Equipment and Material XA (1) N1 (EPR) Derate Display Assy - Marconi Avionics P/N 8706-00028 XA B. Replace display XA (1) Pull out display assy with fingers or a vice-grip with smooth jaws. XA (2) Insert new display and press firmly into the internal connector. XA C. Display Test XA (1) Check N1 (EPR) derate display by slewing the derate toggle switch XA up and down.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:747飞机维护手册AMM CHAPTER 34 - NAVIGATION 第34章导航1(106)