TASK 32-11-27-400-001
Installation of the MLG Torque Links
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : WHEN YOU DO A MAINTENANCE TASK THAT USES COMMON GREASE, USE ONLY
_______ GREASES OF THE SAME SPECIFICATION (IT IS PERMITTED TO USE DIFFERENT BRANDS IF THEIR SPECIFICATIONS ARE THE SAME). DO NOT MIX GREASES THAT HAVE CLAY THICKENERS WITH GREASES THAT HAVE LITHIUM THICKENERS. THIS MIXTURE CAN CHANGE THE LUBRICATION PROPERTIES OF THE GREASE. IF YOU USE GREASES OF DIFFERENT TYPES (SPECIALLY THOSE WITH CLAY THICKENERS AND LITHIUM THICKENERS), DECREASE THE SERVICE INTERVALS OF THE AIRCRAFT (BY HALF, FOR EXAMPLE) SPECIFIED IN THE MAINTENANCE PLANNING DOCUMENT. DO THIS FOR APPROXIMATELY THREE OR FOUR SERVICES (REFER TO YOUR IN-SERVICE DATA TO FIND THE NUMBER OF SERVICES BEST ADAPTED TO YOUR AIRCRAFT).
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 460006226 1 BULLET-ALIGNMENT 460006227 1 ALIGNMENT PIN
1EFF : ALL 1 32-11-27Page 408 1 1 May 01/05 1 1 1CES 1 B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 Material No. 04-022 Material No. 05-047 Material No. 09-016 Material No. 11-026
Material No. 19-003
C. Expendable Parts
USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)C Z-11.904 ANTI COR. COMPOUND(HIGH TEMP.SILICONE SEALANT) (Ref. 20-31-00)USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R
R
R R R R R
4 tab washers
4 tab washers
5 cotter pin
5 cotter pin
5 cotter pin
7 cotter pin
7 cotter pin
7 cotter pin
10 tab washers
10 tab washers
11 tab washers
11 tab washers
14 cotter pin
14 cotter pin
16 cotter pin
16 cotter pin
18 washer(s)
26 cotter pin
32-11-11 52F-24032-11-11 52G-24032-11-11 52C-050 32-11-11 52F-05032-11-11 52G-05032-11-11 52C-050 32-11-11 52F-05032-11-11 52G-050 32-11-11 52F-24032-11-11 52G-240 32-11-11 52F-24032-11-11 52G-240 32-11-11 52F-11032-11-11 52G-110 32-11-11 52F-11032-11-11 52G-11032-11-11 52C-13032-11-11 51A-010
1EFF : ALL 1 32-11-27Page 409 1 1 May 01/04 1 1 1CES 1 D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 07-12-00-582-002 Jacking for Main Gear Wheel Change 12-22-32-640-001 Lubrication of the MLG and Doors 20-28-00-869-002 Table of the Maximum Permitted Resistance Values 20-28-00-912-004 Electrical Bonding of Components With Conductive
Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-11-12-000-001 Removal of the MLG Hydraulic Dressings 32-11-12-400-001 Installation of the MLG Hydraulic Dressings 32-11-27-200-001 Check Torque Links for Excessive Play 32-11-29-400-001 Installation of the Torque Link Damper 2823GM, 2824GM 32-11-43-000-001 Removal of the 1M and 2M Harnesses from the MLG Leg 32-11-43-400-002 Installation of the 1M and 2M Harnesses on the MLG
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(96)
