(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-11-19Page 421 1 1 Feb 01/04 1 1 1CES 1 LOCK SPRINGS - MLG - INSPECTION/CHECK
_____________________________________
TASK 32-11-19-200-001
R Visual Check of Main Landing Gear Downlocking Springs and Sidestay Center Joint R Links and Cuffs
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 321119-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice R
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-11-19-991-001 Fig. 601
1EFF : ALL 1 32-11-19Page 601 1 1 Feb 01/02 1 1 1CES 1
3. Job Set-up
__________
Subtask 32-11-19-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
(4)
On the panel 110VU, make sure that the GRAVITY GEAR EXT handle is
folded into the center console. R
4. Procedure
_________
(Ref. Fig. 601/TASK 32-11-19-991-001)
Subtask 32-11-19-210-050
R A. Visual Inspection of the MLG Lock-Springs and Sidestay Center Joint Links R and Cuffs
(1)
Examine the lock-springs for:
-impact damage
-distortion
-scores
-corrosion.
(2)
Make sure that:
-the lock-springs (3) and (6) are correctly attached to the sidestay and the center joint link (4).
(3)
Examine the spacer (2) for signs of impact damage, wear and corrosion.
(4)
Make sure as far as possible that the cotter pins (1) and (5) are serviceable and correctly installed.
1EFF : ALL 1 32-11-19Page 602 1 1 Feb 01/02 1 1 1CES 1
R MLG Lock Springs, Sidestay Center Joint Links Figure 601/TASK 32-11-19-991-001
1EFF : 1 1 1CES ALL 1 111 32-11-19 Page 603 Aug 01/01
(5) Make sure that the center joint links (4) are correctly attached to the lugs of the cuff (7).
5. Close-up________
Subtask 32-11-19-942-050
A. Removal of Equipment
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R (2) Remove the safety barriers.
R (3) Remove the warning notice(s).
1EFF : ALL 1 32-11-19Page 604 1 1 Feb 01/02 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-105, 151-154, 201-207,
TASK 32-11-19-200-004
Detailed Inspection of Main Landing Gear Downlocking Springs and Sidestay Center Joint Links and Cuffs WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________ 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(82)
