(k) Put the bracket (24) in position on the lockstay and install the washers (21) and the bolts (22). TORQUE the bolts (22) to between
0.4 and 0.45 m.daN (35.39 and 39.82 lbf.in).
R (35) Do the dimensional check of the proximity sensors on the side-stay R assembly (6) (Ref. TASK 32-31-73-200-001).
(36) Do the detailed dimensional check of the MLG lockstay assembly (Ref. TASK 32-11-00-220-003).
(37) Apply SEALANTS (Material No. 09-016) to: R - the ends of the cardan joints (5) and (12)
-
the ends of the pin (26)
-
the heads of the bolts (4) and (22)
-
the nuts (1), (9) and (30)
-
the washers (3), (8), (21), (27) and (29)
-
the locking washer (10).
NOTE : Do not apply sealant between the washer (8) and the flanged
____
bush of the side-stay bracket.
(38)
Lubricate the side-stay assembly (6) through the greasers (Ref. TASK 12-22-32-640-001).
(39)
Install the MLG actuating cylinder (Ref. TASK 32-31-46-400-001).
**ON A/C ALL
Subtask 32-11-16-942-050
D. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
Subtask 32-11-16-865-054
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
1EFF : ALL 1 32-11-16Page 452 1 1 Nov 01/04 1 1 1CES 1 Subtask 32-11-16-869-053
F. Aircraft Maintenance Configuration
(1)
If you did not de-energize the aircraft electrical circuits, put the aircraft back to the ground configuration (Ref. TASK 32-00-00-860-002).
(2)
Connect the isolation coupling of the PTU (Ref. TASK 29-23-00-860-002).
(3)
Pressurize the applicable hydraulic reservoirs (Ref. TASK 29-14-00-614-002).
Subtask 32-11-16-720-050
G. Test
(1)
Do a functional test of the Normal Extension and Retraction of the L/G (Ref. TASK 32-31-00-720-002).
(2)
Do a functional test of the Free-Fall Extension System (Ref. TASK 32-33-00-720-001).
Subtask 32-11-16-790-050
H. Check the Hydraulic System for Leaks
(1) Make sure that all the connections that you have moved are tightened, and that there are no hydraulic leaks.
5. Close-up
________ Subtask 32-11-16-586-050
A. Lower the Aircraft
(1) Lower the aircraft off jacks (Ref. TASK 07-11-00-586-002). Subtask 32-11-16-942-051
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
1EFF : ALL 1 32-11-16Page 453 1 1 Nov 01/04 1 1 1CES 1
(3) Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
1EFF : ALL 1 32-11-16Page 454 1 1 Nov 01/04 1 1 1CES 1 LOCK STAY - MLG - REMOVAL/INSTALLATION
______________________________________
TASK 32-11-17-000-001
Removal of the MLG Lock Stay
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific spatula No specific trestle No specific warning notice No specific access platform 2 m (6 ft. 7 in.)
1EFF : ALL 1 32-11-17Page 401 1 1 May 01/04R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(56)
