(8)
Remove the pin (30) and the washers (31).
(9)
Remove the cotter pin (35), the nut (36) and the washer (37). Discard the cotter pin (35).
(10)
Use a spatula that is not metal, to remove the sealant from the blanking cap, then remove the blanking cap.
(11)
Remove the pin (29) and the washer (28).
(12)
Move the lock stay away from the side stay and remove the washers (27).
(13)
Remove the cotter pin (10), the nut (11), the washers (9), the bracket (8) and the bolt (5). Be careful not to drop the bolt (5) inside the MLG leg.
R (14) Discard the cotter pin (10) and the bolt (5).
(15)
Hold the lock stay, which weighs 3.4 kg (7.50 lb) and carefully disengage the cardan bracket (4) from the MLG leg assembly. Put the lock stay on a trestle.
(16)
If the lock stay is to be replaced, do the steps that follow:
(a)
Remove the cotter pin (12), the nut (7) and the washer (6). Discard the cotter pin (12).
(b)
Remove the pin (2) and the washer (3), move the cardan bracket
(4) away from the cardan joint (1) and collect the washers (13).
1EFF : 001-003, 051-052, 1 32-11-17Page 405 1 1 Aug 01/05 1 1 1CES 1
MLG Lockstay - Removal/Installation
Figure 401/TASK 32-11-17-991-001- 12 (SHEET 1)
R 1EFF : 001-003, 051-052, 1 32-11-17Page 406 1 1 May 01/05 1 1 1CES 1
MLG Lockstay - Removal/Installation
Figure 401/TASK 32-11-17-991-001- 22 (SHEET 2)
R 1EFF : 001-003, 051-052, 1 32-11-17Page 407 1 1 May 01/05 1 1 1CES 1
MLG Lockstay - Removal/Installation
Figure 401A/TASK 32-11-17-991-001-A13 (SHEET 1)
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-17Page 408 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
MLG Lockstay - Removal/Installation
Figure 401A/TASK 32-11-17-991-001-A23 (SHEET 2)
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-17Page 409 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
MLG Lockstay - Removal/Installation
Figure 401A/TASK 32-11-17-991-001-A33 (SHEET 3)
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-17Page 410 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(c)
Remove these parts:
-
the nut (26), the washer (25) and the bolt (24)
-
the nut (20), the washer (21) and the bolt (23)
-
the proximity-sensor bracket (22)
-
the proximity sensor (19) (Ref. TASK 32-31-73-000-001).
(d)
Hold the target bracket (16) and remove the nuts (15) and the washers (14).
(e)
Remove the target bracket (16).
(f)
Remove these parts:
-
the nuts (18) and the washers (17)
-
the bolts (44), (45) and (48)
-
the bracket (46).
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-11-17-020-050-A
A. Removal of the MLG Lock Stay
CAUTION : SAFETY THE SIDE-STAY TO PREVENT ITS MOVEMENT WHEN YOU REMOVE
_______ THE LOCK-STAY. THE SIDE-STAY WEIGHS 54.8kg (120.8lb).
(1)
Disconnect the lock springs at the top attachments (Ref. TASK 32-11-19-000-003).
(2)
Disconnect the connector of the electrical cable (9) from the proximity sensor (7) and remove the bolts (12) and the clips (11). Move the electrical cable (9) away from the bracket (8) and safety in this position.
(3)
Put blanking caps on the disconnected electrical connectors.
(4)
Remove the cotter pin (36), the nut (35) and the washer (34). Discard the cotter pin (36).
(5)
Remove the pin (33) and the washer (32). Move the lock-stay actuating-cylinder eye-end away from the lock stay and remove the washers (37).
(6)
Move the lock-stay actuating-cylinder away from the lock stay and safety in this position.
1EFF : ALL 1 32-11-17Page 411 1 1 Aug 01/05 1 1 1CES 1
(7)
Remove the cotter pin (44), the nut (45) and the washer (43). Discard the cotter pin (44).
(8)
Remove the pin (41) and the washers (42).
(9)
Remove the cotter pin (46), the nut (47) and the washer (48). Discard the cotter pin (46).
(10)
Remove the pin (40) and the washer (39).
(11)
Move the lock stay away from the side stay and remove the washers (38).
(12)
Remove the cotter pin (20), the nut (19) and the washer (18). Discard the cotter pin (20).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(58)
