(16)
Make sure that the dimension X for the 1M harness is 150.0 mm (5.9055 in.).
(17)
Make sure that the dimension Y for the 2M harness is 280.0 mm (11.0236 in.).
(Ref. Fig. 403A/TASK 32-11-43-991-002-A)
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-43Page 439 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(18)
Put the band-clamps (33) in position around the line-support blocks.
(19)
Visually inspect each harness for correct routing and installation.
(20)
Tighten the screws (32).
(21)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-048) to the screws (32).
(a)
Mark the screws (32) with red STRUCTURE PAINTS (Material No. 16-016).
(b)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-048) to the backshells of all the electrical connectors that you removed.
(c)
Mark the backshells of all the electrical connectors that you removed with red STRUCTURE PAINTS (Material No. 16-016).
(d)
Apply a layer of SEALANTS (Material No. 09-016) to all the bolts and washers that you installed.
R **ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 32-11-43-410-062
C. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the applicable access panel 574AB(674AB).
(3)
Remove the access platform(s).
(4)
Close the applicable MLG door (Ref. TASK 32-12-00-410-001).
1EFF : ALL 1 32-11-43Page 440 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 32-11-43-410-062-A
C. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panel 574AB(674AB).
(3)
Remove the access platform(s).
(4) Close the applicable MLG door (Ref. TASK 32-12-00-410-001).
**ON A/C ALL
Subtask 32-11-43-865-057
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
**ON A/C 001-049, 101-149, 151-199, 201-299,
Subtask 32-11-43-740-052
E. Test
(1)
Do a BITE Test of the MLG system (Ref. TASK 32-69-00-740-001).
(2)
Do an operational test of the normal braking system (Ref. TASK 32-42-00-710-001).
(3)
For the 1M harness, do an operational test of the brake temperature system (Ref. TASK 32-47-00-710-001).
1EFF : ALL 1 32-11-43Page 441 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 051-099,
Subtask 32-11-43-740-052-B
E. Test
(1)
Do a BITE Test of the MLG system (Ref. TASK 32-69-00-740-001).
(2)
Do an operational test of the normal braking system (Ref. TASK 32-42-00-710-001).
(3)
For the 1M harness:
(a)
Do an operational test of the brake temperature system (Ref. TASK 32-47-00-710-001).
(b)
Do an operational test of the TPIS (Ref. TASK 32-49-00-710-001).
(4)
For the 2M harness, do an operational test of the brake cooling system (Ref. TASK 32-48-00-710-001).
R **ON A/C 301-399, 401-499,
Subtask 32-11-43-740-052-A
E. Test
(1)
Do a BITE Test of the MLG system (Ref. TASK 32-69-00-740-001).
(2)
Do an operational test of the normal braking system (Ref. TASK 32-42-00-710-001).
(3)
For the 1M harness, do an operational test of the brake temperature system (Ref. TASK 32-47-00-710-001).
(4)
For the 2M harness, do an operational test of the brake cooling system (Ref. TASK 32-48-00-710-001).
R 1EFF : 051-099, 301-399, 401-499, 1 32-11-43Page 442 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
5. Close-up
________ Subtask 32-11-43-942-055
A. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-11-43Page 443 1 1 May 01/05R 1 1 1CES 1
TASK 32-11-43-000-003
Removal of the 1M and 2M Harnesses from the MLG Axle
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(119)
