(b)
Remove the pin (20) and the washers (19).
(c)
Remove the cotter pin (14), the nut (15) and the washer (13). Discard the cotter pin (14).
(d)
Remove the pin (21), the washer (22) and the washers (12).
(e)
Safety the electrical components.
(f)
Put blanking caps on the electrical dressings, the proximity switches and the targets.
(5)
Move the lockstay away from the side-stay (6) and temporarily safety the lockstay in this position.
(6)
Install the SPLINT ASSEMBLY - SIDE STAY (98D32104013001) on the side-stay (6) with:
-
the cables to the wing surface
-
the strap to the wing surface
-
the center joint of the side-stay (6), located in the center hole of the SPLINT ASSEMBLY - SIDE STAY.
(7)
Tighten the strap and connect the cables to the hook. Tighten the cable.
NOTE : Before you remove the circlip (11), make sure that all the
____
related parts are clean.
(8) Remove the circlip (11) as follows:
(a)
Use an applicable tool to release the tail of the circlip (11) from the key slot of the lock washer (10).
(b)
Hold the tail of the circlip (11) with a pair of thin-nose pliers.
(c)
Carefully pull the circlip (11) (in a clockwise direction) until it releases from the chamfered slot in the nut (9).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-18Page 414 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(9) Remove the locking washer (10) from the nut (9).
(10)
Use the TUBE SPANNER (460005834) to remove the nut (9) and remove the washer (8) from the cardan joint (7).
(11)
Loosen the strap (but not fully) on the SPLINT ASSEMBLY - SIDE STAY.
(12)
Move the side-stay (6) around the side-stay center joint so that the cardan joint (7) comes out of the MLG attachment lugs.
NOTE : Before you remove the circlip (4), make sure that all the
____
related parts are clean.
(13)
Remove the circlip (4) as follows:
(a)
Use an applicable tool to release the tail of the circlip (4) from the key slot of the lock washer (3).
(b)
Hold the tail of the circlip (4) with a pair of thin-nose pliers.
(c)
Carefully pull the circlip (4) (in a clockwise direction) until it releases from the chamfered slot in the nut (2).
(14)
Remove the lock washer (3) from the nut (2).
(15)
Use the TORQUE ADAPTOR (460005812) to remove the nut (2) and remove the washer (1) from the cardan joint (5).
(a)
Move the side-stay (6) so that the cardan joint (5) comes out of the side-stay bracket. Tighten the strap to prevent movement of the side-stay (6).
(b)
Lower the side-stay (6) on to the trestle and disconnect the cables from the hook.
(16)
If you are to replace the side-stay (6), remove the SPLINT ASSEMBLY -SIDE STAY. (Ref. Fig. 403/TASK 32-11-18-991-004)
(17)
Remove the seal (32) from the bush (33). Discard the seal (32).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-18Page 415 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 301-399,
R Subtask 32-11-18-020-052-A
R A. Removal of the MLG Side-Stay
R WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE MLG SIDE-STAY. IT_______
R WEIGHS 62.5kg (137.5lb).
R (1) Remove the MLG actuating cylinder (Ref. TASK 32-31-46-000-001).
R (2) Remove the lock springs (Ref. TASK 32-11-19-000-001).
R (3) Remove the lockstay actuating cylinder (Ref. TASK 32-11-21-000-001).
R (4) Disconnect the lockstay assembly as follows:
R CAUTION : MAKE SURE THAT THE ELECTRICAL DRESSINGS, THE PROXIMITY_______
R SWITCHES AND THE TARGETS ARE PROTECTED. THIS PREVENTS
R DAMAGE WHILE THE LOCKSTAY IS SAFETIED.
R (a) Remove the cotter pin (17), the nut (16) and the washer (18).
R Discard the cotter pin (17).
R (b) Remove the pin (20) and the washers (19).
R (c) Remove the cotter pin (14), the nut (15) and the washer (13).
R Discard the cotter pin (14).
R (d) Remove the pin (21), the washer (22) and the washers (12).
R (e) Safety the electrical components.
R (f) Put blanking caps on the electrical dressings, the proximity
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架2(66)
