-------------------------------------------------------------------------------
R R R R R R R | FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | 8.986 | 8.995 | | | 8.979 | | | | OD 58 |(0.3537) |(0.3541) | | |(0.3535) | | | | | | | 0.005 | 0.029 | | | 0.043 | | | | | (0.0001)| (0.0011)| | |(0.0016)| | DD | 9.000 | 9.015 | | | | 9.022 | | | ID 5 |(0.3543) |(0.3549) | | | |(0.3551) | | -------------------------------------------------------------------------------
Subtask 21-52-24-220-054
F. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt (56) and the ID of the bushing (58).
NOTE : If any of the components are 'out of limits' then you must____ replace them.
-------------------------------------------------------------------------------
R R R R R R R | FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | 6.325 | 6.335 | | | 6.318 | | | | OD 56 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.015 | 0.040 | | | 0.054 | | | | | (0.0005)| (0.0015)| | |(0.0021)| | DD | 6.350 | 6.365 | | | | 6.372 | | | ID 58 |(0.2500) |(0.2505) | | | |(0.2508) | | -------------------------------------------------------------------------------
Subtask 21-52-24-220-055
G. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt (56) and the ID of the shouldered bushing (4).
NOTE : If any of the components are 'out of limits' then you must____ replace them, - for item (4) (Ref. CMM 215211) and (Ref. CMM 215212).
-------------------------------------------------------------------------------
R R R R R R R | FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | 6.325 | 6.335 | | | 6.318 | | | | OD 56 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.015 | 0.035 | | | 0.049 | | | | | (0.0005)| (0.0013)| | |(0.0019)| | DD | 6.350 | 6.360 | | | | 6.367 | | | ID 4 |(0.2500) |(0.2503) | | | |(0.2506) | | -------------------------------------------------------------------------------
Subtask 21-52-24-220-056
H. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bushing (38) and the ID of the shouldered bushing (8).
NOTE : If any of the components are 'out of limits' then you must____ replace them, - for item (8) (Ref. CMM 215211) and (Ref. CMM 215212).
-------------------------------------------------------------------------------
R R R R R R R | FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | EE | 8.986 | 8.995 | | | 8.979 | | | | OD 38 |(0.3537) |(0.3541) | | |(0.3535) | | | | | | | 0.005 | 0.029 | | | 0.043 | | | | | (0.0001)| (0.0011)| | |(0.0016)| | EE | 9.000 | 9.015 | | | | 9.022 | | | ID 8 |(0.3543) |(0.3549) | | | |(0.3551) | | -------------------------------------------------------------------------------
Subtask 21-52-24-220-057
J. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt (40) and the ID of the bushing (38).
NOTE : If any of the components are 'out of limits' then you must____ replace them.
-------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR CONDITIONING 空调 4(80)
