R R (h) Put the rod-end (2) in position in the support rod and adjust it until you get the dimension 'B'.
R (i) Dimension 'B':
1_ For the support rod (71), 496.0 +0.2 -0.2 mm (19.5275 +0.0078 -0.0078 in.).
2_ For the support rod (73), 276.4 +0.2 -0.2 mm (10.8818 +0.0078 -0.0078 in.).
3_ For the support rod (74), 266.0 +0.2 -0.2 mm (10.4724 +0.0078 -0.0078 in.).
4_ For the support rod (75), 212.5 +0.2 -0.2 mm (8.3661 +0.0078 -0.0078 in.).
5_ For the support rod (77), 278.5 +0.2 -0.2 mm (10.9645 +0.0078 -0.0078 in.).
6_ For the support rod (78), 132.4 +0.2 -0.2 mm (5.2126 +0.0078 -0.0078 in.).
7_ For the support rod (79), 173.1 +0.2 -0.2 mm (6.8149 +0.0078 -0.0078 in.).
8_ For the support rods (80) and (82), 436.4 +0.2 -0.2 mm (17.1811 +0.0078 -0.0078 in.).
9_ For the support rod (81), 215.5 +0.2 -0.2 mm (8.4842 +0.0078 -0.0078 in.).
R R NOTE : Make sure that the fixed rod-end and the adjustable____ rod-end (2) are in line with each other.
R (j) Check that the rod-end (2) is in safety.
R R R NOTE : A probe of diameter 0.8 mm (0.0314 in.) should not go____ through the inspection hole (4) in the applicable support rod.
R R (k) Bend back the tabs of the washer (1) against the nut (3) so that it is locked and safetied.
R R (l) Move the heat shrink tubing into position over the inspection hole (4) and the nut (3).
R R R (m) Use an applicable heat gun and shrink the tubing until it is tight.
(2) For the rod-end (2):
(a) Remove the heat shrink protective cover from the applicable support rod.
(b) Bend back the lock tabs on the washer (1) and loosen the nut (3).
(c) Remove the rod-end (2) together with the washer (1) and the nut (3).
(d) Remove and discard the washer (1) and remove the nut (3) from the rod-end (2).
(e) Put the nut (3) in position on the new rod-end (2) and screw it on as far as it will go.
(f) Put the new washer (1) in position on the rod-end (2).
(g) Put an applicable sized piece of heat shrink tubing on the body of the support rod.
(h) Put the rod-end (2) in position in the support rod and adjust it until you get the dimension 'B'.
R (i) Refer to Para. E. (1) (i) 1_, 2_, 3_, 4_, 5_, 6_, 7_, 8_ and 9_.
(j) Tighten the nut (3) against the washer (1) and the support rod.
R R (k) Make sure that the rod-end (2) and the fixed rod-end are in line with each other.
(l) Check that the rod-end (2) is in safety.
R R NOTE : A probe of diameter 0.8 mm (0.0314 in.) should not go____ through the inspection hole (4) in the applicable support rod.
(m) Bend back the tabs of the washer (1) against the nut (3) so that it is locked and safetied.
(n) Move the heat shrink tubing into position over the inspection hole (4) and the nut (3).
(o) Use an applicable heat gun and shrink the tubing until it is
tight.
R (3) For both the fixed rod-end and the adjustable rod-end (2):
R (a) Replace the applicable support rod Ref. IPC 21-52-03.
R
R **ON A/C 051-052,
R TASK 21-52-00-300-002 R Air Cycle Machine - Compressor Return Duct - Preformed Packing Replacement R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR CONDITIONING 空调 4(26)
