(1)
Clean the greasers with a clean MISCELLANEOUS (Material No. 19-003).
(2)
Lubricate the spoiler servo-control bearings with COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-024) through the greasers until new grease comes out.
(3)
Remove the unwanted grease from the greasers and the spoiler servo-control bearings with a clean MISCELLANEOUS (Material No. 19-003).
(4)
Make sure that the greaser ball has seated correctly after lubrication.
1EFF : ALL 1 12-22-27Page 323 1 1 May 01/04R 1 1 1CES 1
Spoiler Servo Control Bearing - Lubrication Point Figure 304/TASK 12-22-27-991-007
1EFF : 1 1R 1CES ALL 1 11 1 12-22-27 Page 324 May 01/04
5. Close-up
________ Subtask 12-22-27-865-059
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 22CE, 21CE1, 21CE2, 21CE3.
Subtask 12-22-27-866-055
B. Aircraft Configuration
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Retract the flaps fully (Ref. TASK 27-50-00-866-009). Subtask 12-22-27-942-055
C. Removal of the Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 12-22-27Page 325 1 1 May 01/04R 1 1 1CES 1
TASK 12-22-27-640-006
Lubrication of all Slat Track Rollers, Pinion Bearings, Pinions and Rack Teeth
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 278468-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific brush No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific access platform 4 m (13 ft. 1 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 04-024 AIB AIMS 09-06-001 SYNTHETIC GREASE FOR FLAP & SLAT MECHANISM (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 12-22-27Page 326 1 1 May 01/04R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground
27-80-00-866-005 Retracting the Slats on the Ground
57-41-37-000-004 Removal of the Pressure-Relief Panels 521AB(621AB),
521CB(621CB), 521EB(621EB), 522AB(622AB),
522CB(622CB)
57-41-37-000-006 Removal of the Access Panels 522FB(622FB),
522JB(622JB), 522KB(622KB), 522LB(622LB),
522NB(622NB), 522QB(622QB), 522SB(622SB),
522UB(622UB)
57-41-37-400-002 Installation of the Pressure-Relief Panels
521AB(621AB), 521CB(621CB), 521EB(621EB),
522AB(622AB), 522CB(622CB)
57-41-37-400-006 Installation of the Access Panels 522FB(622FB),
522JB(622JB), 522KB(622KB), 522LB(622LB),
522NB(622NB), 522QB(622QB), 522SB(622SB),
522UB(622UB)
SIL 12-008 (for corrective action)
12-22-27-991-002 Fig. 305
3. Job Set-up__________
(Ref. Fig. 305/TASK 12-22-27-991-002) Subtask 12-22-27-941-056
A. Safety Precautions
(1) Put the safety barriers in position. Subtask 12-22-27-866-056
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM SERVICING 2(7)