Subtask 12-22-27-866-052
B. Aircraft Maintenance Configuration
(1)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(2)
On panel 114VU, make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
(3)
Put a warning notice on the slat/flap control lever (panel 114VU) to tell persons not to operate the flap system.
(4) Put the access platform in position under the applicable flap track. Subtask 12-22-27-865-056
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________ R **ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 302/TASK 12-22-27-991-001)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 311 1301-399, 1May 01/05 1 1 1CES 1R Flap Track Carriage Rollers - Lubrication Points R Figure 302A/TASK 12-22-27-991-001-A
R 1EFF : 301-399, 1 12-22-27Page 312 1 1 May 01/04 1 1 1CES 1
**ON A/C 301-399,
(Ref. Fig. 302A/TASK 12-22-27-991-001-A) R **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 12-22-27-640-053
A. Lubricate the Flap Track Carriage-Rollers NOTE : When you do a maintenance task that uses common grease, refer to
____
the SIL (Ref. SIL 12-008).
(1)
Clean the greasers with a clean MISCELLANEOUS (Material No. 19-003).
(2)
Lubricate the flap track carriage-rollers with COMMON GREASE (Material No. 04-024) or COMMON GREASE (Material No. 04-004) through the greasers until new grease comes out.
(3)
Remove the unwanted grease from the greasers and the flap track carriage-rollers with a clean MISCELLANEOUS (Material No. 19-003).
(4)
Make sure that the greaser ball has seated correctly after lubrication.
5. Close-up
________ R **ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 302/TASK 12-22-27-991-001)
**ON A/C 301-399,
(Ref. Fig. 302A/TASK 12-22-27-991-001-A)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 313 1301-399, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
Subtask 12-22-27-865-057
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 12-22-27-866-053
B. Aircraft Configuration
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Retract the flaps fully (Ref. TASK 27-50-00-866-009).
Subtask 12-22-27-942-054
C. Removal of the Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 314 1301-399, 1May 01/05 1 1 1CES 1R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
TASK 12-22-27-640-004- 01 Lubrication of all Flap Track Carriage Rollers and No.1 Track Drive Lever Arm WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 275446-01
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 2(4)
