(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 12-22-27Page 320 1401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C ALL
TASK 12-22-27-640-005
Lubrication of Spoiler No.1 to 5 Servo Control Bearings
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 276400-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific adjustable access platform 4 m (13 ft. 1 in.)
1EFF : ALL 1 12-22-27Page 321 1 1 May 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 04-024 AIB AIMS 09-06-001 SYNTHETIC GREASE FOR FLAP & SLAT MECHANISM (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground SIL 12-008 (for corrective action) 12-22-27-991-007 Fig. 304
3. Job Set-up
__________
Subtask 12-22-27-941-055
A. Safety Precautions
(1) Put the safety barriers in position.
Subtask 12-22-27-866-054
B. Aircraft Maintenance Configuration
(1)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(2)
On panel 114VU, make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
(3)
Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flap system.
1EFF : ALL 1 12-22-27Page 322 1 1 May 01/04R 1 1 1CES 1
(4) Put the adjustable access platform in position under the applicable spoiler.
Subtask 12-22-27-865-058
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
4. Procedure
_________
(Ref. Fig. 304/TASK 12-22-27-991-007)
Subtask 12-22-27-640-054
A. Lubrication of Spoiler No.1 to 5 Servo Control Bearings
NOTE : When you do a maintenance task that uses common grease, refer to
____
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 2(6)
