R - the door hinges and the guide fittings.
R (c) Apply the silicone grease, SPECIAL MATERIALS (Material No. 05-
R 001) to the door frame. Apply the silicone grease, COMMON GREASE
R (Material No. 04-011) to the pressure seals.
R (d) Apply the silicone grease, SPECIAL MATERIALS (Material No. 05-
R 001) the silicone grease, COMMON GREASE (Material No. 04-011) or
R the pure mineral vaseline, COMMON GREASE (Material No. 04-012) to
R the vent panel seals.
R (e) Apply the temporary protective compound, STORAGE PRESERVATION
R (Material No. 15-005A) to the external control handles and
R shafts.
R (f) Lubricate the door hinges and the guide fittings. Apply the
R temporary protective compound, STORAGE PRESERVATION (Material No.
R 15-005A) to the latch assemblies and the latch spools.
COLD WEATHER MAINTENANCE - POWER PLANT - MAINTENANCE PRACTICES
______________________________________________________________
TASK 12-31-71-660-001
1. Reason for the Job
Cold Weather Maintenance - Power Plant __________________ This procedure gives the cold weather maintenance practices for the engines.
2. Job Set-up Information______________________ Not Applicable __________
3. Job Set-up
Subtask 12-31-71-941-050
A. Not applicable
4. Procedure
_________ Subtask 12-31-71-660-050
A. Ice can form in the engine intakes and freeze the fan, therefore you must do a careful examination of the engine intake and fan before engine start up. Attention should be paid to the forward and rear sides of the fan blades in order to determine whether clear ice is present. Use hot air blower to remove all traces of ice and residual water before engine start up.
Subtask 12-31-71-660-051
B. Freezing Points
(1) The oil temperature is also a limitation. For the approved oils and the oil limitation temperatures, you must refer to the engine manufacturer's data.
SAMPLING FOR ANALYSIS - DESCRIPTION AND OPERATION
_________________________________________________
1. General
_______ This section defines the different fluid samplings which may be carried out for an analysis.
INTEGRATED DRIVE GENERATOR OIL - SERVICING
__________________________________________
TASK 12-32-24-281-001
Sampling of the IDG Oil for Analysis
WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
WARNING : WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES.
_______
HOT OIL CAN BURN YOUR EYES AND SKIN.
IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.
1. Reason for the Job
__________________
To find the cause of the oil contamination (skydrol, fuel, water, chlorine, oil degradation, and other causes).
R NOTE : The best location and time to get an oil sample is at the case drain
____ R after operation of the engine, when the IDG oil is at the operating R temperature (80 deg.C (176 deg.F)).
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 5.7 l (1.5 USgal)
No specific transparent bottle 1 l (0.26 USgal)
No specific warning notice
No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
DH13PM 1 TANK - ENGINE OIL FILLING UP
B. Consumable Materials
------------------------------------------------------------------------------- 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM SERVICING 2(69)
