4. Procedure
_________ (Ref. Fig. 311/TASK 12-22-52-991-022) R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 312/TASK 12-22-52-991-029)
**ON A/C 001-002,
Subtask 12-22-52-640-063
A. Lubrication Procedure CAUTION : DO NOT USE A HIGH-PRESSURE GREASE-GUN. HIGH-PRESSURE
_______ LUBRICATION CAN CAUSE DAMAGE TO THE COMPONENTS.
(1)
Apply COMMON GREASE (Material No. 04-004) with a hand grease gun to the grease fitting of the subsequent components:
-
the safety-pin guide fitting (1)
-
the spring rod of the slide control handle (2)
-
the telescopic rod of the slide arming mechanism (3)
-
the hook of the interlock mechanism (4)
-
the spring rod of the escape-slide control mechanism (5)
(2)
Make sure that the bushes of the safety-pin guide fitting (1) are in their correct position after the lubrication procedure.
(3)
Lubricate the flexible control (6) as follows:
(a)
Loosen the lower seal nut (7) by three turns minimum.
(b)
Apply COMMON GREASE (Material No. 04-004) to the upper grease fitting of the flexible control (6).
NOTE : Use of a high pressure grease gun is not permitted.
____ Operate the hand grease gun until the grease comes in view at the holes of the lower seal nut (7).
(c)
TORQUE the lower seal nut (7) to between 0.35 and 0.45 m.daN
(30.97 and 39.82 lbf.in).
(d)
Loosen the upper seal nut (8) by three turns minimum.
Lubrication of the Safety Guide Fitting and Door Arming/Disarming Mechanism R Figure 311/TASK 12-22-52-991-022
1EFF : ALL 1 12-22-52Page 348 1 1 May 01/05 1 1 1CES 1
Lubrication of the Girt Bar Spring
Figure 312/TASK 12-22-52-991-029
R 1EFF : 003-049, 051-099, 101-149, 151-199, 1 12-22-52Page 349 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(e) Apply COMMON GREASE (Material No. 04-004) to the upper grease fitting of the flexible control (6).
NOTE : Operate the hand grease gun until the grease comes in view
____ at the holes of the upper seal nut (8).
(f) TORQUE the upper seal nut (8) to between 0.35 and 0.45 m.daN
(30.97 and 39.82 lbf.in).
(4) Remove the unwanted grease with a lint-free cloth. R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 12-22-52-640-063-A
A. Lubrication Procedure CAUTION : DO NOT USE A HIGH-PRESSURE GREASE-GUN. HIGH-PRESSURE
_______ LUBRICATION CAN CAUSE DAMAGE TO THE COMPONENTS.
(1)
Apply COMMON GREASE (Material No. 04-004) with a hand grease gun to the grease fitting of the subsequent components:
-
the safety-pin guide fitting (1)
-
the spring rod of the slide control handle (2)
-
the telescopic rod of the slide arming mechanism (3)
-
the hook of the interlock mechanism (4)
-
the spring rod of the escape-slide control mechanism (5)
(2)
Make sure that the bushes of the safety-pin guide fitting (1) are in their correct position after the lubrication procedure.
(3)
Lubricate the flexible control (6) as follows:
(a)
Loosen the lower seal nut (7) by three turns minimum.
(b)
Apply COMMON GREASE (Material No. 04-004) to the upper grease fitting of the flexible control (6).
NOTE : Operate the hand grease gun until the grease comes in view
____ at the holes of the lower seal nut (7).
(c)
TORQUE the lower seal nut (7) to between 0.35 and 0.45 m.daN
(30.97 and 39.82 lbf.in).
(d)
Loosen the upper seal nut (8) by three turns minimum.
(e)
Apply COMMON GREASE (Material No. 04-004) to the upper grease fitting of the flexible control (6).
NOTE : Operate the hand grease gun until the grease comes in view
____ at the holes of the upper seal nut (8).
(f) TORQUE the upper seal nut (8) to between 0.35 and 0.45 m.daN
(30.97 and 39.82 lbf.in).
(4) Apply COMMON GREASE (Material No. 04-004) with a brush to the spring of girt bar trigger.
(5) Remove the unwanted grease with a lint-free cloth. **ON A/C ALL
5. Close-up
________ Subtask 12-22-52-410-063
A. Close Access
(1)
Install the removed door insulation and door lining (Ref. TASK 25-23-46-400-001) and (Ref. TASK 25-23-46-400-002).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 2(33)
