(a)
Remove the protection caps.
(b)
Lubricate the gasket (19) with the beeswax.
(c)
Put the gasket (19) on the boss on the diffuser and combustor case.
(d)
Install the fuel injector (5) in the boss on the diffuser and combustor case.
NOTE: Turn or lift the fuel injector, as it is necessary, to
____ install the fuel injector in the diffuser and combustor case.
1) Align the bolt holes in the support with the bolt holes in the diffuser and combustor case.
(e)
If you will install the No. 18 fuel injector, put the bracket (10) on the fuel injector (5) with the bolt holes aligned.
(f)
Lubricate the threads of the bolts (21) with engine oil.
(g)
Install the bolts (21) to attach the fuel injector (5), and the bracket (10) if applicable, to the diffuser and combustor case. 1) Tighten the bolts (21) to 65-85 pound-inches (7.3-9.6
newton-meters). 2) Tighten the bolts (21) again to 65-85 pound-inches (7.3-9.6 newton-meters) until you keep the necessary torque. 3) Install the lockwire or safety cable and safety cable ferrule to the bolts (21).
(h)
For the No. 18 fuel injector, attach the oil supply tube to the bracket (10) with the steps that follow: 1) Lubricate the threads of the bolts (60) with engine oil. 2) Attach the tube clamp (62) for the oil supply tube to the
bracket (10) with the bolts (60) and nut (61). a) Tighten the nut (61).
(i)
Lubricate the new packing (20) with the petroleum jelly.
(j)
Install the new packing (20) to the groove on each of the three fuel injectors (5).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N01 Page 480F ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(k)
Lubricate the new packings (3) with the petroleum jelly.
(l)
Install the new packings (3) on each end of the transfer tube (2).
(m)
Install the transfer tube (2) in the supply tube (1).
(n)
Connect the fuel manifold (4) to the fuel injectors (5).
NOTE: You will tighten the fuel manifold nuts after you do the
____ leak check of the fuel manifold.
1) Lubricate the threads of the fuel injectors (5) with engine
oil. 2) Connect the fuel manifold (4) to the fuel injectors (5). 3) Tighten the fuel manifold nuts (4) with your hand.
(o) Connect the supply tube (1) to the fuel manifold (4).
NOTE: You will tighten the supply tube nut after you do the
____ leak check of the fuel manifold.
1) Lubricate the threads of the fuel manifold inlet (4) with
engine oil. 2) Connect the fuel supply tube (1) to the fuel manifold (4). 3) Tighten the supply tube nut (1) with your hand.
S 794-321-N00
(2) Do this task, which is found at the end of this section: "Fuel Manifolds Leak Check"
NOTE: After you do the leak check of the fuel manifold, you must
____
install all remaining parts you removed.
S 414-251-N00
(3)
Install the oil tank (AMM 79-11-01/401) if it was removed.
H.
Return the Aircraft to its Usual Condition
S 864-252-N00
(1)
For the applicable engine, remove the DO-NOT-CLOSE tag and close this circuit breaker:
(a)
P6 Main Power Distribution Panel
1) 6L10 FUEL CONT VALVE ENG 1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N01 Page 480G ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
2) 6L11 FUEL CONT VALVE ENG 2
3) 6L12 FUEL CONT VALVE ENG 3
4) 6L13 FUEL CONT VALVE ENG 4
S 864-253-N00
(2)
For the applicable engine, remove the DO-NOT-CLOSE tags and close these circuit breakers:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 发动机燃油和控制 1(79)
