R (7) Do the pressure refuel with auto control.
R (8) If the fault continues:
R (a) Set the MCDU to INPUT PARAMETERS page 3, (the bit position -R state cross-reference).
R (b) Examine the bit positions in the Table 1 that follows:
R NOTE : Not all the refuel signals are monitored by the FQIC to be
____ R shown on the INPUT PARAMETERS page 3. R The signals that are not shown on the INPUT PARAMETERS are R identified in Table 2 with the Para number given for R direct entry into the Trouble-shooting task.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 301-399, ∞∞28-25-00∞∞∞∞∞∞∞∞∞∞Page 212
May 01/04 CESR Table 1, Bit position - State Cross-reference R -----------------------------------------------------------------------------R | Bit | Bit indication | FQIC pin | Input/Output | Para| R |position| (active state) | allocation | Voltage Level | No | R |--------|---------------------------------|------------|---------------|-----| R | J2 | Battery power | C08H I/P | Ground | (15)| R | K2 | Cockpit Preselector Fault | C07C I/P | Open circuit | (19)| R | H2 | Refuel door open | C08C I/P | Ground | (23)| R | A2 | Cockpit refuel selected | C07E I/P | 28VDC | (27)| R | P2 | Cockpit preselector decrement | C05C I/P | Ground | (31)| R | L2 | Refuel Panel Presel Fault | C07H I/P | Open circuit | (34)| R | E2 | Refuel selected | C08E I/P | 28VDC | (38)| R | N2 | Cockpit preselector increment | C05D I/P | Ground | (42)| R | M2 | Refuel Indicator Fault | C07G I/P | Open circuit | (45)| R | R2 | Refuel preselector decrement | C04J I/P | Ground | (49)| R | D2 | Refuel bus powered | C09E I/P | 28VDC | (52)| R | Q2 | Refuel preselector increment | C04K I/P | Ground | (56)| R | | | | | | R -----------------------------------------------------------------------------
R NOTE : If an above signal is not correct, (a 1 not shown), refer
____ R to the Para. shown in the end column.
R NOTE : The preselector(s) INC/DEC switch input to the FQIC will
____ R only show a 1 while the INC/DEC switch is held in that R position. Not at the central/rest position.
R Table 2, Refuel signals not shown on the INPUT PARAMETERS page 3 R -----------------------------------------------------------------------------R | Signal | FQIC pin | Voltage Level | Para | R | | allocation | (active state)| No | R |---------------------------------------|------------|---------------|--------| R | Aircraft Ground/Flight (GND/FLT) | B05F I/P | Ground (GND) | (9)(a) | R | Right refuel valve supplied | C08B I/P | 28VDC | (59) | R | Left refuel valve supplied | C08A I/P | 28VDC | (63) | R | Center refuel valve supplied | C09B I/P | 28VDC | (67) | R | Right refuel valve return | C08J O/P | 28VDC | (71) | R | Left refuel valve return | C08K O/P | 28VDC | (74) | R | Center refuel valve return | C09J O/P | 28VDC | (77) | R | | | | | R -----------------------------------------------------------------------------
R (9) For the automatic refuel mode to be active check the conditions that R follow in conjunction with the Table 1 above or as directed:
R (a) The ground/flight discrete input is set to ground:
R 1_ Remove the FQIC (3QT) from its rack connector (Ref. AMM TASKR 28-42-34-000-001).
R 2_ With a multimeter check to see if the FQIC rack connect pinR B05F is at ground potential.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 301-399, ∞∞28-25-00∞∞∞∞∞∞∞∞∞∞Page 213
May 01/04 CES
R 3_ If pin B05F is at ground potential reinstall the FQIC (Ref.
R AMM TASK 28-42-34-400-001).
R 4_ If the pin B05F is not at ground potential do a wiring check
R of the:
R - aircraft wiring between the FQIC (3QT) rack connector pin
R B05F and MSW-REFUEL.DEFUEL CTL DOOR POSITION (20QU), (Ref.
R ASM 28-42/03).
R - aircraft wiring between the FQIC (3QT) rack connector pin
R B05F and RELAY-L/G POSITION, SYS 1 (11GB), (Ref. ASM 28-R 42/03).
R 5_ Repair all wiring and connectors.
R 6_ Reinstall the FQIC (3QT) (Ref. AMM TASK 28-42-34-400-001).
R (b) The refuel selected discrete is active. The logic for this,
R incorporated in the aircraft wiring, is condition 1_ or 2_ below:
R 1_ Refuel panel door open and the MODE SELECT switch on the
R external refuel panel set to REFUEL.
R 2_ The cockpit refuel panel power switch set to on, and the
R cockpit refuel panel CTL (Control) switch set to on.
R (c) All the REFUEL VALVE switches are set to NORMAL.
R (10) For an automatic refuel to start make that the conditions are as
R follows:
R (a) Refuel bus power has been present for sufficient time to allow
R the high level sensors to settle in thier true states.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 FUEL 燃油2(65)
