On the PORTABLE DATA LOADER:
-
the TRANSF IN PROG message is displayed
-after the time has elapsed the TRANSFCOMPLETE message comes into view
On the PORTABLE DATA LOADER:
-the < < MDDU READY > > indicationcomes into view
-after 40s the DISPLAY SYSTEM VERSION INCONSISTENCY message comes into view on the CAPT PFD and ND display units.
(1)
On the PORTABLE DATA LOADER, set the ON/OFF switch to the OFF position
(2)
Disconnect the cable from the PORTABLE DATA LOADER connector
R 1EFF : 401-499, 1 31-60-00Page 332 1 1 Aug 01/05 1 1 1CES 1
(3)
Install a blanking cap on the connector. Subtask 31-60-00-862-055
B.
Put the aircraft back to its initial configuration.
(1)
On the keyboard of the MCDU, push the MCDU MENU key to get the MCDU MENU page
(2)
On the MCDU, set the BRT knob to OFF
(3)
Put the disks in the storage box
(4)
Do the EIS stop procedure (Ref. TASK 31-60-00-860-002).
(5)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
(6)
Make sure that the work area is clean and clear of tool(s) and other items.
R 1EFF : 401-499, 1 31-60-00Page 333 1 1 Aug 01/05 1 1 1CES 1
TASK 31-60-00-610-007 UP LOADING Procedure of the DMC1 with the MDDU
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure
3. Job Set-up
__________ Subtask 31-60-00-861-058
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002)
(2)
Do the EIS start procedure (Ref. TASK 31-60-00-860-001)
R 1EFF : 401-499, 1 31-60-00Page 334 1 1 Aug 01/05 1 1 1CES 1 Subtask 31-60-00-865-062
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/MCDU/1 11CA1 B01 49VU L/G/LGCIU/SYS1/NORM 1GA C09 49VU EIS/ECAM/CTL/PNL 15WT E12 49VU EIS/DMC1/SPLY 10WT1 E11 49VU EIS/DMC3/STBY/SPLY 14WT1 E10 49VU EIS/DMC1/SWTG 21WT1 E09 49VU EIS/DMC3/SWTG 21WT3 E07 121VU DATA/LOADER/SPLY 3TD J16 121VU DLS&/DLRB/SPLY 5TD J15 121VU AUTO FLT/MCDU/2 11CA2 N20 121VU EIS/DMC3/SPLY 10WT3 Q09 121VU EIS/DMC2/SPLY 10WT2 Q08 121VU EIS/DMC2/SWTG 21WT2 R08
4. Procedure_________
Subtask 31-60-00-860-073
A. Make sure that the aircraft is in the GROUND configuration:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the ECAM control panel: On the SD
-press the pushbutton to call the - the BLEED page comes into view BLEED page
-make sure that the GND indication On the SD:
is displayed - GND is displayed in white in the middle area of the page.
R 1EFF : 401-499, 1 31-60-00Page 335 1 1 Aug 01/05 1 1 1CES 1 Subtask 31-60-00-610-057
B. UP LOADING Procedure of the DMC1:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the MDDU:
-the < < MDDU READY > > indication is shown
1. On the MCDU 1(2):
-put the BRT/DIM switch to ON
2. In the stowage box
-Get the disks related to the EIS
3.
On the overhead C/B control panel 49VU: - open the EIS/DMC1/SPLY circuit
breaker 10WT1
4.
On the DATA Loading selector:
-set the ON/OFF switch to ON
-
push the PREV/NEXT key until you get DMC1 NOT SELECTED indication
-
push the SEL CTL to get DMC1 SELECTED indication.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 指示/记录系统 7(75)
