(3)
Remove the nut (40), the bolt (37) and the washer (38) and disconnect the bonding jumper (39).
HP Manifold
Figure 401/TASK 29-11-14-991-001
R 1EFF : 001-049, 051-058, 101-101, 1 29-11-14Page 404 1 1 May 01/05 1 1 1CES 1
HP Manifold Figure 401A/TASK 29-11-14-991-001-A
R 1EFF : 059-099, 102-149, 151-199, 201-299, 1 29-11-14Page 405 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(4)
Remove the nut (50) and the bolt (48) and disconnect the P-clip (49) from the structure attachment.
(5)
Loosen the pipe end-fitting (52) and disconnect the pipe (51) from the union (53).
(6)
Loosen the pipe end-fitting (47) and remove the pipe (51) from the aircraft.
(7)
Loosen the pipe end-fitting (21) and disconnect the pipe (20) from the union (22).
(8)
Loosen the pipe end-fitting (18) and disconnect the pipe (17) from the check valve 1022GM.
(9)
Loosen the pipe end-fitting (25) and disconnect the pipe (24) from the union (26).
(10)
Loosen the pipe end-fitting (2) and disconnect the pipe (1) from the union (3).
(11)
Hold the manifold (13) and remove the five bolts (15) and the five washers (16).
(12)
Remove the manifold (13).
(13)
Put blanking plugs on the disconnected line ends and the manifold ports.
1EFF : ALL 1 29-11-14Page 406 1 1 May 01/99R 1 1 1CES 1
TASK 29-11-14-400-001
Installation of the HP Manifold of the Green Hydraulic System
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container
No specific plastic or wooden scraper
No specific warning notices
No specific access platform 2.8 m (9 ft. 2 in.)
No specific 1 BAG - PLASTIC
No specific 8 PLUG - BLANKING
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00
to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft)
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A
CORROSION INHIBITING BRUSH CONSISTENCY
(Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3
CORROSION INHIBITING LOW ADHESION SEALANT
(Ref. 20-31-00)
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
7 back-up ring 29-11-14 02B-120
9 back-up rings 29-11-14 02B-170
11 square-section seals 29-11-14 02 -110
11 square-section seals 29-11-14 02B-280
19 O-ring 29-11-14 02 -020
19 O-ring 29-11-14 02B-060
27 O-ring 29-11-14 20 -020
27 O-ring 29-11-14 20A-020
28 O-ring 29-11-14 02B-040
29 back-up rings 29-11-14 20 -010
29 back-up rings 29-11-14 20A-010
33 back-up rings 29-11-14 02 -100
33 back-up rings 29-11-14 02B-270
35 square-section seals 29-11-14 02 -110
35 square-section seals 29-11-14 02B-280
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM HYDRAULIC POWER 液压2(15)
