Subtask 27-51-18-010-050
D. Get Access
(1)
Put the access platform in position:
-
FOR 29CV
below the access panel 575FB
-
FOR 30CV
below the access panel 675FB.
(2)
Remove the applicable access panel:
-
FOR 29CV
remove 575FB (Ref. TASK 57-51-37-000-004)
-
FOR 30CV
remove 675FB (Ref. TASK 57-51-37-000-004).
4. Procedure
_________
(Ref. Fig. 401/TASK 27-51-18-991-001, 402/TASK 27-51-18-991-002)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-51-18-020-050
A. Removal of the Asymmetry-Position Pick-Off Unit
CAUTION : MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU
_______ DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Electrically disconnect the APPU.
(a)
Disconnect the plug (4) from the connector A and the plug (5) from the connector B.
(b)
Install blanking caps on the plugs (4) and (5) and the connectors A and B.
(2)
Hold the APPU (3), remove the bolts (2) and the washers (1), then disengage and remove the APPU (3).
(3)
Install a tie-wrap (6) behind the locking plate (7) to lock the APPU
(3) in position.
1EFF : ALL 1 27-51-18Page 405 1 1 May 01/04R 1 1 1CES 1
Flap APPU - Zero Datum Settings and Locations Figure 402/TASK 27-51-18-991-002
1EFF : 1 1R 1CES ALL 1 11 1 27-51-18 Page 406 May 01/04
TASK 27-51-18-400-001
Installation of the Asymmetry-Position Pick-Off Unit 29CV (30CV)
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
No specific access platform 3.5 m (11 ft. 6 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
Material No. 15-007 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)AIB TN 10138 TYPE II GRADE 1
CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
Material No. 19-003 (Ref. 20-31-00)USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground
27-54-00-710-001 Operational Test of the Flap System
27-51-18-991-001 Fig. 401
27-51-18-991-002 Fig. 402
R FOR FIN 29CV
R 57-51-37-000-004 Removal of the Access Panels
R 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB
R (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)
R 57-51-37-400-004 Installation of the Access Panels
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(96)
