5. Close-up
________ Subtask 27-51-00-942-061
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
FLAPS ELECTRICAL CONTROL AND MONITORING - ADJUSTMENT/TEST
_________________________________________________________ TASK 27-51-00-740-001 Read-out of Class 3 Faults in the Flap System WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
31-32-00-869-002 Procedure for Class 3 Faults Reading
1EFF : ALL 1 27-51-00Page 501 1 1 May 01/05R 1 1 1CES 1
3. Job Set-up
__________
Subtask 27-51-00-941-066
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flap controls.
4. Procedure
_________ Subtask 27-51-00-869-051 R A. Read-out of Class 3 Faults in the Flap System.
(1) Read for Class 3 faults in the flap system (Ref. TASK 31-32-00-869-002).
5. Close-up
________
Subtask 27-51-00-942-066
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 27-51-00-740-002 Bite Test of the Slat and Flap Control Computers (Flap System) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
R NOTE : IGNORE ALL THE ECAM WARNINGS WHEN THE COMPUTER IS IN THE MENU MODE.
____
1. Reason for the Job
__________________ Self Explanatory NOTE : Refer to SIL 27-116 for SFCC In-Service Standards and SFCC
____
Combinations.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST F/CTL Page
3. Job Set-up
__________
Subtask 27-51-00-941-071
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flight controls.
Subtask 27-51-00-860-057
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(38)
