A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(119)_航空信息_民用航空_通用航空

曝光台注意防骗网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

NOTE : The interconnecting strut can have one or two
____ inspection/setting holes. If there are two, use the hole that is not blocked by the aircraft structure.
(2) If necessary, adjust the actuating rod of the interconnecting strut so that you can install the PIN-SETTING as follows:
(a)
Align the rod-end (9) with the flap until you can install the bolt (16).

(b)
If necessary, remove and discard the lockwire from the locknut (10).

1EFF : ALL 1 27-51-44Page 611 1 1 May 01/04R 1 1 1CES 1

(d)
Adjust the nut (12) until you can install the PIN-SETTING. Make sure that you can see the threads of the rod-end (9) through the check hole. If you cannot see the threads of the rod-end (9) through the check hole, check the flap rigging (Ref. TASK 27-51-00-820-003).

(e)
Tighten the locknut (10).

(f)
Install the washer (13) and the nut (15).

(g)
Torque the nut (15) to between 1.1 and 1.7 m.daN (97.34 and

150.44 lbf.in).
NOTE : It is possible to have a clearance between the bush and
____
the strut attachment bracket.

(h)
Install a new cotter pin (14).

(i)
If you loosened the locknut (10), TORQUE it to between 5.1 and

5.9 m.daN (37.61 and 43.51 lbf.ft).
(j) Safety the locknut (10) with MISCELLANEOUS (Material No. 19-010).
(3)
Remove the PIN-SETTING from the inspection/setting hole in the interconnecting strut.

(4)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to:

-
the head of the bolt (16)

-
the nut (15)

-
the washer (13)

-
the cotter pin (14).

(5)
Do an operational test of the flap interconnecting strut and the flap-attachment failure-detection sensors (Ref. TASK 27-51-00-710-002).

Subtask 27-51-44-865-069
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
1EFF : ALL 1 27-51-44Page 612 1 1 May 01/04R 1 1 1CES 1

Subtask 27-51-44-710-058
D. Test
(1)
Get access to the flight controls (F/CTL) page of the MCDU (Ref. TASK 31-32-00-860-006).

(2)
Do this test of the flap interconnecting strut and the
flap-attachment failure-detection sensors:

-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the MCDU: On the MCDU:
1. Push (in) the line key < SFCC 1. - the MCDU shows the SFCC 1 page.
2. Push (in) the line key SYSTEM STATUS FLP >. - the MCDU shows the SFCC 1 SYSTEMSTATUS FLAP page. These subsequent messages must not occur: - FLP 1 NO SFCC 2 DATA CHECK WIRING &
SFCC 2
- FLP 1 FAULTY FLP 2 DATA CHECK SFCC
1 OR 2
- NO LGCIU 1 DATA CHECK WIRING TO FLP
1
- FLP LH PROX SNSR 1 MISADJUSTMENT
and FLP LH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP LH PROX SNSR 1 OR WIRING TO
LGCIU 1
- FLP LH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP RH PROX SNSR 1 MISADJUSTMENT
and FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP RH PROX SNSR 1 OR WIRING TO
LGCIU 1
- FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2.
3. Push (in) the line key <RETURN. - the MCDU shows the SFCC 1 page.
4. Push (in) the line key <RETURN. - the MCDU shows the SYSTEM REPORT/TEST PAGE.