5. Close-up
________ Subtask 27-51-00-410-061
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panels:
(a) For the LH wing, install:
-573AB, 573CB (Ref. TASK 57-51-37-400-002)
-575AB (Ref. TASK 57-51-37-400-004)
(b) For the RH wing, install:
-673AB, 673CB (Ref. TASK 57-51-37-400-002)
-675AB (Ref. TASK 57-51-37-400-004) Subtask 27-51-00-942-080
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SENSOR FLAP ATTACHMENT FAILURE DETECTION (37CV,38CV,39CV,40CV)
______________________________________________________________ REMOVAL/INSTALLATION
____________________ TASK 27-51-15-000-002 Removal of the Proximity-Sensors of the Interconnecting Strut WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
To give ATA reference to agree with CFDS message.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-51-44-000-002 Removal of the Proximity-Sensor of the Interconnecting Strut
3. Job Set-up
__________ Subtask 27-51-15-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flight controls.
4. Procedure
_________ Subtask 27-51-15-020-050
A. Remove the Proximity Sensor
(1) Remove the applicable proximity sensor (Ref. TASK 27-51-44-000-002).
TASK 27-51-15-400-002 Installation of the Proximity-Sensors of the Interconnecting Strut WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
To give ATA reference to agree with CFDS message.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-51-44-400-002 Installation of the Proximity-Sensor of the Interconnecting Strut
3. Job Set-up
__________ Subtask 27-51-15-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the flight controls.
4. Procedure
_________ Subtask 27-51-15-420-050
A. Install the Proximity Sensor
(1) Install the applicable proximity sensor (Ref. TASK 27-51-44-400-002).
5. Close-up
________ Subtask 27-51-15-942-050
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(92)
