A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(62)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

R  (1) Remove and discard the cotter pin (5) from the nut (4). 
R R  (2) At the track 3 position, remove the nut (4), the washer (3), the bolt (1) and the serrated plate (2). 
R R  (3) At the track 4 position, remove the bolt (7), the washer (8) and the serrated plate (9). 
R R R R  (4) Adjust the forward eccentrics (6) and (10) in sequence by the amount shown on the label attached to flap track beam 3. Make sure that the adjustments are in small equal increments, to move the flap deflection by the same amount. 
R R R R  NOTE : Flap movement is opposite to the value shown on the label____ attached to the flap track 3 beam assembly. For an 'up' or '+' label value the flap must be moved down. For a 'down' or '-' label value the flap must be moved up.

 

R R  (5) At the track 3 position, temporarily install the serrated plate (2) with the bolt (1), the washer (3) and the nut (4). 
R R  (6) At the track 4 position, temporarily install the serrated plate (9) with the bolt (7) and the washer (8). 
R R  (7) Make sure that the punched/painted marks on the forward eccentrics align. 
R R  (8) Remove the sharks fin flap rigging kit (Ref. TASK 27-51-00-820-008) or (Ref. TASK 27-51-00-820-009). 
R  **ON A/C ALL
 5. Close-up________
 Subtask 27-51-00-942-068
 A. Removal of Equipment
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the safety barriers.
 (3) Remove the warning notice(s).
 (4) Remove the access platform(s).
 (5) Remove the ground support and maintenance equipment, the special and standard tools and all other items. 

R 1EFF : ALL 1 27-51-00Page A500 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,

 

 TASK 27-51-00-820-008
 Adjustment of the Flap Rigged Position With the Sharks Fin Tool (A318/319/320)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Flap rigging is done:
 -
when specified in an AMM Task

 -
when specified in a TSM Task

 -if you think the the flap rigged position is incorrect.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A501 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  circuit breaker(s) safety clip(s)
 No specific  ruler-steel
 No specific  safety barriers
 No specific  warning notice
 No specific  access platform 3 m (9 ft. 10 in.)
 No specific  Torque Wrench : range 0.00 to 1.20 m.daN
 (0.00 to 9.00 lbf.ft)
 No specific  Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft)
 No specific  Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00 to 75.00 lbf.ft)
 No specific  Torque Wrench : range 2.00 to 20.00 m.daN
 (15.00 to 150.00 lbf.ft)
 98D27504002000  1 TOOL-FLAP ADJUSTING
 98D27504005000  2 PIN RIGGING-FLAPS (TRACK 1)
 98D27504006000  3 PIN RIGGING FLAPS
 98D27504030001  1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
 98D27504035000  1 TORQUE ADAPTOR-TRUNNION NUT
 98D27504038000  3 KIT-FLAP RIGGING
 98D27504038001  3 KIT-FLAP RIGGING
 98D27504039000  1 TOOL RESTRAINING TK1
 98D27504040000  1 TOOL RESTRAINING TK1
 98D27504041000  1 TOOL FLAP ADJUSTING
 98D27504082000  2 TOOL - FLAP ADJUSTING, 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(62)